Post by: Elk whack master on July 13, 2012, 09:05:09 PM
Post by: Sabotloader on July 14, 2012, 07:40:05 AM
Has anyone done this and how much would it help? :dunno:
Most Extremes come some what floated, but often the stock has changed over time and may be touching the barrel in spots. Floating is really not the best way to obtain accuracy although it might be the cheapest.
There are a couple of testrs that you might do to make sure you might need to float the barrel... the easiest one is to take a piece of paper such as a crispy dollar bill - insert it under the barrel and slide it along the underside of the barrel between the barrel and the stock...
I am not at the right computer to offer you the whole right up about the testing but later today I will put my 25 cent test.
Checking the Fit of Knight stock
Rob, relieving the stickiness of that should be a really easy fix....
I wrote this up for a guy on Hunting Net the other day - i will repost it here. Look through it and see if it makes sense to you. I firmly believe the sticky stock will affect your accuracy...
Quote:
Can i get a little info on making sure i don't have any stock to barrel issues? I have seen info on tv about how a free floating barrel helps and heard of different procedures of seating the barrel. I will be putting a new stock on my gun very soon (broke the original one), and don't want to have issues there.
I can share some information with you for sure... One thing to remember 'floating' a barrel is not the best for accuracy it is the ‘cheapest’ so that is why you see many companies floating barrels. Companies can not afford to spend the time (money) bedding a barrel to the stock properly so the best thing is to 'float' them. With a wood stock the temperature of the barrel on the wood will make the POI change unless they barrel is bedded in glass or some such feature. In a composite stock if the barrel were bedded into the barrel channel correctly the heat would not be a problem but the flexion of the forearm of the inexpensive stock create a POI shift - so the answer 'float' the barrel.
In your case... since I think you said you have a Knight and if you are getting a Knight composite stock you might not have any of these problems. When I put a barreled action in a Knight stock I set the action in the stock and start the lug screw in. Tighten it with the Allen wrench until it starts to pull the action down. Then stand the gun vertically with the recoil pad on the floor. Gently, and honestly i am not that gentle, tap the gun on the floor to assure that the recoil lug is all the way back in the pocket. Then tighten the lug screw up snugly to hold it all in place. Forgot to say make sure the ram rod is not in place.
When you have the lug screw in tight place the gun in a horizontal position and squeeze the nose of the forearm and the barrel together as tight as you can. If there is no movement – you’re done the barrel is seated on and in the barrel channel. Put the ram rod in and repeat the test. If the test is the same you’re done... go shoot it and give it a check for accuracy.
If during the squeeze test (ram rod removed) the barrel moves down into the stock or the stock moves up to the barrel... release the grip and note if the barrel moves (on its own) back to the original location. Everything should be good - the barrel is floating. Next repeat the test again noting where the barrel returns to. At this time grip the barrel and the forearm of the stock and pull them apart easily. If you feel the barrel stick at some point then you have a problem. If the barrel appears to lift slightly but when you release it - it returns to the original location and you feel no points of stickiness - you are good. Put the ram rod in and repeat the test.
During the squeeze testing if you felt some stickiness in the spring of the floating barrel you will then to do some very light sanding in the barrel channel to relieve the tight spot. You might be able to locate the tight spot by running a dollar bill under the barrel and between the stock to locate the tight spot. Do not sand any more than you need, in fact in my little world the thickness of a single dollar bill is the max thickness the barrel should be off the stock. I normal use a strip of white computer paper for this test it is thinner than a dollar bill - heck it might be worth more than the dollar bill also!!!
Hope this might help you... when you get your new stock and if I can help give a shout....