Post by: Kc_Kracker on May 13, 2022, 05:31:24 PM
- I know you can reload brass what about steel or aluminum
- how do I know what powder primers and bullets to use in each thing I reload ?
- as I'm setting up my reloading room should I be setting it up so that I'm using my equipment from a standing position or sitting like at a workbench?
Sent from my moto g stylus 5G using Tapatalk
Post by: callturner on May 13, 2022, 06:21:37 PM
Post by: Oh Mah on May 13, 2022, 06:49:50 PM
As to how many loads per brass, there are a lot of variables to that. if you load hot much less. Magnums esp. Weatherby like to swell and you will need a collet die to fix(if you run them hot). I have ran .300 win mag 15 16 times with 0 problems as long as they were all consistently sized. keep them as close to the fire form as you can and anneal when needed and you will get a long life out of each brass. I also only use upper end brass also. :tup:
Post by: NRA4LIFE on May 13, 2022, 06:52:25 PM
Post by: TRD1911 on May 13, 2022, 06:54:04 PM
- how many times can a cartridge or brass be reloaded
- I know you can reload brass what about steel or aluminum
- how do I know what powder primers and bullets to use in each thing I reload ?
- as I'm setting up my reloading room should I be setting it up so that I'm using my equipment from a standing position or sitting like at a workbench?
Sent from my moto g stylus 5G using Tapatalk
Finally a topic that I can feel somewhat helpful on! I'm usually the one soaking up the knowledge spread around here.
-# of reloads depends on how hot you reload your cartridge, how tight the tolerances of your weapon are, how much you are sizing and what type of sizing you are doing (neck sizing/bumping, full length sizing...). I dont really keep track of # of reloads for anything except for my precision rifle loads. The things to watch out for is split necks, loose primer pockets (you will feel a difference when hand priming which I prefer), and a ridge inside of the case along the shoulder. Of course case head seperations and all that are signs that the batch is done.
-There are youtube videos out there of guys loading steel cases. Seems like it works once or twice but for the sake of your vision, and your firearm, I wouldnt recommend it. If you're that hard up for brass let me know and I'll try to help, ha!
-As mentioned above the loading manuals are your best friend when it comes to componenet combinations; projectile weight, case trim length, sizing guide, powder types and charges, primers (large vs small; standard vs magnum). There are free manuals online from many of the major powder and bullet manufactures. Of course they are biased towards their product. Everyone will tell you to start low and work up your load. This is the best possible advice when it comes to putting together your first loads.
-I like to reload while standing. My posture is horrible when I'm doing repetative tasks while sitting (currently hunched over typing). I'm also always reaching for something; powder scale, projectiles, calipers....its just easier for me to do standing. I'm only loading for 1-2 hours at a time and have a mat in front of my bench so its not a big deal.
Post by: Kc_Kracker on May 13, 2022, 08:54:52 PM
Sent from my moto g stylus 5G using Tapatalk
Post by: Smokeploe on May 13, 2022, 08:58:39 PM
As far as sitting or standing do both, if you feel like sitting the do so, if you feel like standing then do so, it what’s you want to do. Build you reloading bench so you can do both.
Steel or other metals it’s better to stick with brass, to many other variables to deal with.
Remember knowledge is power the more you read the more answers you will find.
Smokeploe
Post by: jasnt on May 13, 2022, 09:10:41 PM
Strongly recommend finding a local reloader to mentor you.