Post by: rebal69972 on January 13, 2012, 09:39:50 PM
Thank you for Any input
Post by: sebek556 on January 13, 2012, 09:45:37 PM
5.56 and 223 have are the same size, where the change between the two is the pressure generated when fired, part of this due to the fact that 5.56 handle heavier bullets than .223
a .223 round has more velocity than the 5.56 (also could be due to the bullet being lighter) so most .223 rifles has less rifling than a 5.56
My understanding(and just my understanding not fact) is you can shoot .223 out of a 5.56x45 but not the other way around. I am sure that there are others on this site which will be more helpful. :tup:
Post by: Gutpile on January 13, 2012, 09:49:19 PM
Post by: KillBilly on January 13, 2012, 09:55:59 PM
Post by: JimmyHoffa on January 13, 2012, 09:58:11 PM
Post by: halflife65 on January 13, 2012, 10:00:56 PM
Post by: rebal69972 on January 13, 2012, 10:10:18 PM
Post by: carpsniperg2 on January 13, 2012, 10:10:28 PM
Post by: FC on January 13, 2012, 10:40:28 PM
Post by: scudmaster on January 13, 2012, 11:20:40 PM
Post by: Bofire on January 14, 2012, 10:46:02 AM
Carl
Post by: grundy53 on February 08, 2012, 02:31:21 PM
Post by: pianoman9701 on February 08, 2012, 02:43:40 PM
Post by: scudmaster on February 08, 2012, 11:21:19 PM
There was a guy in Portland like that - real condescending a-hole. I buy my guns elsewhere now.
Yeah that!!!
Post by: scudmaster on February 08, 2012, 11:25:59 PM
how is the accuracy affected shooting shooting .223 through a 5.56 as opposed to just using 5.56 ammo?
As with any gun, depends what it likes. Often higher pressure leads to more inconsistency of barrel harmonics. so some 5.56 will like lower .223 pressure better, but some will be the opposite. Clear as mud right?
Post by: ICEMAN on February 09, 2012, 05:07:21 AM
Post by: FALFire on February 09, 2012, 05:47:49 AM
Yeah, always confusing. I was given a nice fat box of ammo at xmas, and opened it quickly to check out the round.... I screwed up, it was 5.56 and not .223. So I am sitting on some really nice Federal 5.56 that I cannot shoot. :bash:
What would you be shooting it in?
Post by: ICEMAN on February 09, 2012, 05:52:17 AM
I am no AR expert and did not want to risk the higher pressure I assume I would get with the 5.56 ammo...
Post by: FALFire on February 09, 2012, 06:05:59 AM
Post by: ICEMAN on February 09, 2012, 05:51:16 PM
Post by: FALFire on February 10, 2012, 09:13:23 AM
Even if you have a 223 chamber and feel the 5.56 ammo will cause a problem, then don't use it. Barrel manufactures are well versed in the likely event that most AR15 shooters will simply pickup the cheapest ammo available to blast through their new toys. I have never heard of any AR15 blowing up using one ammo vs the other in these respective chambers. Most people worry about the 223 vs 5.56 issue like it's an evil demon but never even think about proper head spacing and that is even more dangerous than the ammo differences. Putting a new barrel on an AR that has had 20,000 rounds thru it and not replacing the bolt is asking for potential problems. At most what one might experience with 5.56 vs 223 ammo is accelerated wear, bolt guns, however, may be different.
Post by: Special T on February 10, 2012, 02:32:31 PM
Post by: dontgetcrabs on February 10, 2012, 05:22:51 PM
Is firing a 5.56 NATO cartridge in your .223 Remington chambered AR15 dangerous? Or do Internet forum-ninjas and ammunition companies selling you commercial ammo instead of surplus overstate the dangers? Believe it or not, a real danger exists, and some gun owners who think they are doing the right thing may not be safe.
The Cartridges
The .223 Remington and 5.56x45 NATO cartridges are very similar, and externally appear the same. But there are some differences that lie beneath the surface.
The 5.56 case has thicker walls to handle higher pressures, meaning the interior volume of the case is smaller than that of a .223. This will alter the loading data used when reloading 5.56 brass to .223 specs.
Some 5.56 loads have a slightly longer overall length than commercial .223 loads.
The Chambers
The significant difference between the .223 Rem and 5.56 NATO lies in the rifles, rather than the cartridges themselves. Both the .223 and 5.56 rounds will chamber in rifles designed for either cartridge, but the critical component, leade, will be different in each rifle.
The leade is the area of the barrel in front of the chamber prior to where the rifling begins. This is where the loaded bullet is located when a cartridge is chambered. The leade is frequently called the “throat.”
On a .223 Remington spec rifle, the leade will be 0.085”. This is the standard described by the Sporting Arms and Ammunition Manufacturers’ Institute, Inc. (SAAMI). The leade in a 5.56 NATO spec rifle is 0.162”, or almost double the leade of the .223 rifle.
A shorter leade in a SAAMI spec rifle creates a situation where the bullet in a 5.56 NATO round, when chambered, can contact the rifling prior to being fired. By having contact with the rifling prematurely (at the moment of firing), chamber pressure can be dramatically increased, creating the danger of a ruptured case or other cartridge/gun failure.
The reverse situation, a .223 Rem round in a 5.56 NATO gun, isn’t dangerous. The leade is longer, so a slight loss in velocity and accuracy may be experienced, but there is not a danger of increased pressures and subsequent catastrophic failure.
How serious is the danger of firing 5.56 ammo in .223 guns? Dangerous enough that the SAAMI lists 5.56 military ammo as being not for use in .223 firearms in the technical data sheet titled “Unsafe Firearm-Ammunition Combinations.”
ATK, the parent company of ammunition manufacturers Federal Cartridge Company and Speer, published a bulletin entitled “The Difference Between 223 Rem and 5.56 Military Cartridges.” In this bulletin, ATK stated using 5.56 ammo in a .223 rifle could result in “…primer pocket gas leaks, blown cartridge case heads, and gun functioning issues.”
However, the danger may be lower than SAAMI or ATK suggest. In Technical Note #74 from ArmaLite, the company states “millions of rounds of NATO ammunition have been fired safely in Eagle Arms and ArmaLite’s® SAAMI chambers over the past 22 years,” and they have not had any catastrophic failures.
According to ArmaLite:
“Occasionally a non-standard round (of generally imported) ammunition will fit too tightly in the leade, and resistance to early bullet movement can cause elevated chamber pressures. These pressures are revealed by overly flattened primers or by powder stains around the primer that reveal leaking gasses.”
What Do You Have?
So, if you own a rifle chambered for the .223 for 5.56, do you know for which caliber it is really chambered?
Many match rifles are chambered in .223 Remington (SAAMI specs) for tighter tolerances, and theoretically better accuracy.
Many of the AR-15’s currently sold on the market are made for the 5.56 NATO cartridge. If you own one of these, you should be fine with any .223 or 5.56 ammunition.
However, ATK dropped this bomb in the bulletin on the .223/5.56:
“It is our understanding that commercially available AR15’s and M16’s – although some are stamped 5.56 Rem on the receiver – are manufactured with .223 chambers.”
So, even if your AR is stamped 5.56, is it really? Check your owner’s manual or call the company directly and make sure you get an answer you feel comfortable with.
As if the confusion regarding the .223 vs 5.56 chambers wasn’t enough, there is a third possibility in the mix, that is being used by at least one major manufacturer. The .223 Wylde chamber is a modified SAAMI-spec .223 chamber that allows for the safe use of 5.56 NATO rounds, but maintains tighter tolerances for better accuracy.
Yeah, yeah… What’s the bottom line?
Here’s the bottom line. If you want to follow the safest possible course, always shoot .223 Remington ammunition. The .223 Rem cartridge will safely shoot in any rifle chambered for the .223 or 5.56.
If you want to shoot 5.56 NATO rounds, make sure you have a rifle designed for the 5.56 military cartridge. Shooting 5.56 in a normal .223 Rem rifle can result in bad things.
Post by: FALFire on February 10, 2012, 07:20:40 PM
I've been around these things for many years, fired dozens of AR's using both 223 and 5.56 ammo in opposing chambers and have seen perhaps one or two that displayed any problems which were associated with some crap wolf ammo, the early coated junk that gummed up chambers once they got plenty hot. When you are going through hot combat drills dumping 30 round mags like they were candy and having smoke coming out of the barrel for 20 minutes after shooting there should have been at least one that was a problem.....................But there wasn't :dunno:
Again, if you feel unsafe firing 5.56 ammo in a 223 chamber the simple answer is do not do it.
Not saying that it can't happen but if it were a real serious problem someone would have posted the aftermath over and over on the internet.
Post by: rebal69972 on February 11, 2012, 10:44:22 AM
Post by: Helix on February 11, 2012, 10:53:27 AM
I dont remember the reason but like Sebek said. You can shoot .223 and 5.56 out of a 5.56 chamber but should not shoot 5.56 out of a .223 chamber.
Correcto! The 5.56 chamber has a throat that is cut more generously which allows for a higher pressure loading. 223 rounds will fire through it just fine. However the higher pressure 5.56 rounds can cause overpressure in the tighter 223 throat.