collapse

Advertisement


Author Topic: Taller front sight  (Read 1969 times)

Offline gaolista

  • Trade Count: (0)
  • Tracker
  • **
  • Join Date: Mar 2013
  • Posts: 59
  • Location: Bothell
Taller front sight
« on: June 03, 2020, 06:08:35 PM »
I have an ace in the hole peep and am at the front end of the ramp and shooting low at 100.  I cannot find a shorter front sight for the life me. Any advice? Shooting a CVA Optima v2. Thanks in advance.  The title says Taller, I meant Shorter.

Offline j_h_nimrod

  • Non-Hunting & Covid-19 Topics
  • Trade Count: (+1)
  • Sourdough
  • *****
  • Join Date: Aug 2011
  • Posts: 1604
  • Location: Humptulips, WA
Re: Taller front sight
« Reply #1 on: June 03, 2020, 06:46:51 PM »
It should likely be a standard dovetail front sight and not rifle specific. Just measure the height and find a generic replacement with the correct dovetail in a lower height. Look at Midway or Brownellís for a good selection.

Offline gaolista

  • Trade Count: (0)
  • Tracker
  • **
  • Join Date: Mar 2013
  • Posts: 59
  • Location: Bothell
Re: Taller front sight
« Reply #2 on: June 03, 2020, 11:08:15 PM »
It should likely be a standard dovetail front sight and not rifle specific. Just measure the height and find a generic replacement with the correct dovetail in a lower height. Look at Midway or Brownellís for a good selection.
Thanks for the reply. The stock sight isnít a dovetail, so I assume Iíd have to find a dovetail mount too? Iím guessing that is a standard size probably? Thanks for the help!

Offline optic2

  • Trade Count: (0)
  • Hunter
  • ***
  • Join Date: Jul 2017
  • Posts: 206
  • Location: Bothell,WA
  • Groups: BHA, RMEF
Re: Taller front sight
« Reply #3 on: June 03, 2020, 11:47:13 PM »
I have an ace in the hole peep and am at the front end of the ramp and shooting low at 100.  I cannot find a shorter front sight for the life me. Any advice? Shooting a CVA Optima v2. Thanks in advance.  The title says Taller, I meant Shorter.

The real issue is that the rear sight is too far forward, it should be right near the back of the barrel right near the breech plug. It is built this way so you can put a rail on the gun for a scope and not have the stock rear sight interfere. The solution to your problem is to get an Eabco peeprib. Once your rear sight is further back then the stock front sight will work just fine. Plus, if you ever want to throw a scope on then you can (hunt in a firearms restricted area or in a state that allow scopes on a muzzy).

https://www.eabco.net/PeepRib-Peep-Sights-for-CVA-Optima-Kodiak-Wolf-and-Accura_p_13910.html

On mine I removed the sight that came with the peeprib and put a Williams ghost ring on it.

Offline gaolista

  • Trade Count: (0)
  • Tracker
  • **
  • Join Date: Mar 2013
  • Posts: 59
  • Location: Bothell
Re: Taller front sight
« Reply #4 on: June 04, 2020, 05:27:21 AM »
I have an ace in the hole peep and am at the front end of the ramp and shooting low at 100.  I cannot find a shorter front sight for the life me. Any advice? Shooting a CVA Optima v2. Thanks in advance.  The title says Taller, I meant Shorter.

The real issue is that the rear sight is too far forward, it should be right near the back of the barrel right near the breech plug. It is built this way so you can put a rail on the gun for a scope and not have the stock rear sight interfere. The solution to your problem is to get an Eabco peeprib. Once your rear sight is further back then the stock front sight will work just fine. Plus, if you ever want to throw a scope on then you can (hunt in a firearms restricted area or in a state that allow scopes on a muzzy).

https://www.eabco.net/PeepRib-Peep-Sights-for-CVA-Optima-Kodiak-Wolf-and-Accura_p_13910.html

On mine I removed the sight that came with the peeprib and put a Williams ghost ring on it.
Thanks for the reply. I have my ace in the hole rail mounted all the way back and my peep is right in front of the plug and Iím still at the end of the ramp. Might need to get the file out.

Offline trophyhunt

  • Forum Sponsor
  • Trade Count: (+9)
  • Explorer
  • *****
  • Join Date: Nov 2008
  • Posts: 13840
  • Location: Wetside
  • Groups: Wa Wild Sheep Life Member
Re: Taller front sight
« Reply #5 on: June 04, 2020, 06:37:39 AM »
I have an ace in the hole peep and am at the front end of the ramp and shooting low at 100.  I cannot find a shorter front sight for the life me. Any advice? Shooting a CVA Optima v2. Thanks in advance.  The title says Taller, I meant Shorter.

The real issue is that the rear sight is too far forward, it should be right near the back of the barrel right near the breech plug. It is built this way so you can put a rail on the gun for a scope and not have the stock rear sight interfere. The solution to your problem is to get an Eabco peeprib. Once your rear sight is further back then the stock front sight will work just fine. Plus, if you ever want to throw a scope on then you can (hunt in a firearms restricted area or in a state that allow scopes on a muzzy).

https://www.eabco.net/PeepRib-Peep-Sights-for-CVA-Optima-Kodiak-Wolf-and-Accura_p_13910.html

On mine I removed the sight that came with the peeprib and put a Williams ghost ring on it.
Thanks for the reply. I have my ace in the hole rail mounted all the way back and my peep is right in front of the plug and Iím still at the end of the ramp. Might need to get the file out.
Same problem with my same gun.  I've bought two sights and both are almost off the rail, my front site (or what ever is closest to end of barrel), is too tall.  sabatloader sent me a fix but I still need to buy it and see.  there is a topic on here with all the info you should need, I just hope it all works out before muzzy season.  It's been a very frustrating time finding both sites that work together.
ďIn common withĒ..... not so much!!

Offline dc

  • Non-Hunting & Covid-19 Topics
  • Trade Count: (0)
  • Hunter
  • ***
  • Join Date: Jun 2010
  • Posts: 221
  • Location: kelso wash.
Re: Taller front sight
« Reply #6 on: June 04, 2020, 06:45:46 AM »
I also bought the optima last yr and have the same issue. 

Offline trophyhunt

  • Forum Sponsor
  • Trade Count: (+9)
  • Explorer
  • *****
  • Join Date: Nov 2008
  • Posts: 13840
  • Location: Wetside
  • Groups: Wa Wild Sheep Life Member
Re: Taller front sight
« Reply #7 on: June 04, 2020, 06:53:44 AM »
I'm hoping this works.     https://www.muzzle-loaders.com/optics/sights/williams-western-precision-muzzleloading-sight-set-cva-traditions-t-c.html              My only concern is will the site at the end of the barrel still be too tall. 
ďIn common withĒ..... not so much!!

Offline gaolista

  • Trade Count: (0)
  • Tracker
  • **
  • Join Date: Mar 2013
  • Posts: 59
  • Location: Bothell
Re: Taller front sight
« Reply #8 on: June 04, 2020, 02:47:14 PM »
I'm hoping this works.     https://www.muzzle-loaders.com/optics/sights/williams-western-precision-muzzleloading-sight-set-cva-traditions-t-c.html              My only concern is will the site at the end of the barrel still be too tall.
Yeah Iíve looked at the globe, but Iím afraid in lowlight situations having the fiber will probably be better.

Offline gaolista

  • Trade Count: (0)
  • Tracker
  • **
  • Join Date: Mar 2013
  • Posts: 59
  • Location: Bothell
Re: Taller front sight
« Reply #9 on: June 04, 2020, 02:48:40 PM »
I have an ace in the hole peep and am at the front end of the ramp and shooting low at 100.  I cannot find a shorter front sight for the life me. Any advice? Shooting a CVA Optima v2. Thanks in advance.  The title says Taller, I meant Shorter.

The real issue is that the rear sight is too far forward, it should be right near the back of the barrel right near the breech plug. It is built this way so you can put a rail on the gun for a scope and not have the stock rear sight interfere. The solution to your problem is to get an Eabco peeprib. Once your rear sight is further back then the stock front sight will work just fine. Plus, if you ever want to throw a scope on then you can (hunt in a firearms restricted area or in a state that allow scopes on a muzzy).

https://www.eabco.net/PeepRib-Peep-Sights-for-CVA-Optima-Kodiak-Wolf-and-Accura_p_13910.html

On mine I removed the sight that came with the peeprib and put a Williams ghost ring on it.
Thanks for the reply. I have my ace in the hole rail mounted all the way back and my peep is right in front of the plug and Iím still at the end of the ramp. Might need to get the file out.
Same problem with my same gun.  I've bought two sights and both are almost off the rail, my front site (or what ever is closest to end of barrel), is too tall.  sabatloader sent me a fix but I still need to buy it and see.  there is a topic on here with all the info you should need, I just hope it all works out before muzzy season.  It's been a very frustrating time finding both sites that work together.
Thanks for the advice. Iíll have to search thru the threads, any chance you have a link to it?

Offline gaolista

  • Trade Count: (0)
  • Tracker
  • **
  • Join Date: Mar 2013
  • Posts: 59
  • Location: Bothell
Re: Taller front sight
« Reply #10 on: June 04, 2020, 02:50:54 PM »
Iím about ready to get the file out, the other part of the equation that I donít know is just how much lower I need to go. If anyone has experience and would have advice thatíd be awesome! Ideally Iíd like to be able to use the whole ramp and not keep the peep cling onto the front end even after the solution.

Offline MeatMissile

  • Trade Count: (+2)
  • Pilgrim
  • *
  • Join Date: Jun 2018
  • Posts: 31
Re: Taller front sight
« Reply #11 on: June 04, 2020, 05:36:55 PM »
I replaced the factory front sight with a Williams .405 fiberoptic front sight.  Its a standard round cut .8 something to fit my barrel.

Offline gaolista

  • Trade Count: (0)
  • Tracker
  • **
  • Join Date: Mar 2013
  • Posts: 59
  • Location: Bothell

Offline gaolista

  • Trade Count: (0)
  • Tracker
  • **
  • Join Date: Mar 2013
  • Posts: 59
  • Location: Bothell
Re: Taller front sight
« Reply #13 on: June 05, 2020, 02:49:34 PM »
I replaced the factory front sight with a Williams .405 fiberoptic front sight.  Its a standard round cut .8 something to fit my barrel.
Might have to go with something like this one. I assume similar to the Williams one that you switched to.

https://www.midwayusa.com/product/1828810516

Offline gaolista

  • Trade Count: (0)
  • Tracker
  • **
  • Join Date: Mar 2013
  • Posts: 59
  • Location: Bothell
Re: Taller front sight
« Reply #14 on: June 06, 2020, 05:36:18 PM »
Well, after going back and forth, Iíve decided to 3D print shims that will go under the peep rail. 3D printed parts are remarkably strong, Iíll just need to get longer screws. Can anyone confirm they are 8-40 sized screws? Iíll keep you posted how it all works out.

Offline Bango skank

  • Political Topics
  • Trade Count: (+9)
  • Old Salt
  • ******
  • Join Date: May 2014
  • Posts: 5892
  • Location: colville
Re: Taller front sight
« Reply #15 on: June 06, 2020, 06:09:56 PM »
Interesting, i got a 70 year old marlin that had the same issue.  Seller even told me it shot high.  I bottomed out the dovetail and it was still way high.  Ordered a taller fiber optic front from skinner sights and fixed the problem.

Offline optic2

  • Trade Count: (0)
  • Hunter
  • ***
  • Join Date: Jul 2017
  • Posts: 206
  • Location: Bothell,WA
  • Groups: BHA, RMEF
Re: Taller front sight
« Reply #16 on: June 07, 2020, 01:20:42 AM »
I have an ace in the hole peep and am at the front end of the ramp and shooting low at 100.  I cannot find a shorter front sight for the life me. Any advice? Shooting a CVA Optima v2. Thanks in advance.  The title says Taller, I meant Shorter.

The real issue is that the rear sight is too far forward, it should be right near the back of the barrel right near the breech plug. It is built this way so you can put a rail on the gun for a scope and not have the stock rear sight interfere. The solution to your problem is to get an Eabco peeprib. Once your rear sight is further back then the stock front sight will work just fine. Plus, if you ever want to throw a scope on then you can (hunt in a firearms restricted area or in a state that allow scopes on a muzzy).

https://www.eabco.net/PeepRib-Peep-Sights-for-CVA-Optima-Kodiak-Wolf-and-Accura_p_13910.html

On mine I removed the sight that came with the peeprib and put a Williams ghost ring on it.
Thanks for the reply. I have my ace in the hole rail mounted all the way back and my peep is right in front of the plug and Iím still at the end of the ramp. Might need to get the file out.

I see that you're in Bothell. We could meetup at Kenmore rifle range once it's open again and you can try out my rifle.

Offline gaolista

  • Trade Count: (0)
  • Tracker
  • **
  • Join Date: Mar 2013
  • Posts: 59
  • Location: Bothell
Re: Taller front sight
« Reply #17 on: June 07, 2020, 03:13:43 PM »
Well I got my shims printed. 2mm, 3mm, 4mm. Need to get some longer screws, but I imagine it should work. When I get an opportunity to shoot Iíll let you know how it works.


 

Offline kellama2001

  • Women's Board
  • Trade Count: (0)
  • Sourdough
  • *****
  • Join Date: Jul 2015
  • Posts: 1185
  • Location: Eastern Washington
  • My patriotic heart beats red, white and blue
  • Groups: MDF, NWTF, NRA, RMEF, BHA
Re: Taller front sight
« Reply #18 on: June 08, 2020, 08:08:18 AM »
Tagging along, curious to see how this turns out
Of what avail are 40 freedoms without a blank spot on the map?
-Aldo Leopold

Offline WingNut81

  • Trade Count: (0)
  • Pilgrim
  • *
  • Join Date: Jun 2020
  • Posts: 1
  • Location: Arlington
Re: Taller front sight
« Reply #19 on: June 11, 2020, 11:53:16 AM »
I just went through the same thing with the same gun.  I have the Eabco rear peep and used the Marble Uni-ramp #72408 with .875 barrel diameter and .405 sight height.  A super easy and cheap fix.  The rifle shoots spot on with plenty of elevation adjustment up and down.

Offline trophyhunt

  • Forum Sponsor
  • Trade Count: (+9)
  • Explorer
  • *****
  • Join Date: Nov 2008
  • Posts: 13840
  • Location: Wetside
  • Groups: Wa Wild Sheep Life Member
Re: Taller front sight
« Reply #20 on: June 11, 2020, 12:28:50 PM »
I just went through the same thing with the same gun.  I have the Eabco rear peep and used the Marble Uni-ramp #72408 with .875 barrel diameter and .405 sight height.  A super easy and cheap fix.  The rifle shoots spot on with plenty of elevation adjustment up and down.
Well I just ordered the marble uni-ramp, I sure hope this site is tall enough, getting tired of buying sites.
ďIn common withĒ..... not so much!!

Offline MeatMissile

  • Trade Count: (+2)
  • Pilgrim
  • *
  • Join Date: Jun 2018
  • Posts: 31
Re: Taller front sight
« Reply #21 on: June 11, 2020, 07:09:08 PM »
Take the OEM screw to Fastenal and theyíll fix you up.

Online elkhunter1977

  • Trade Count: (0)
  • Hunter
  • ***
  • Join Date: Apr 2012
  • Posts: 135
  • Location: Tri-Cities
Re: Taller front sight
« Reply #22 on: September 25, 2020, 08:31:00 PM »
I have an ace in the hole peep and am at the front end of the ramp and shooting low at 100.  I cannot find a shorter front sight for the life me. Any advice? Shooting a CVA Optima v2. Thanks in advance.  The title says Taller, I meant Shorter.

The real issue is that the rear sight is too far forward, it should be right near the back of the barrel right near the breech plug. It is built this way so you can put a rail on the gun for a scope and not have the stock rear sight interfere. The solution to your problem is to get an Eabco peeprib. Once your rear sight is further back then the stock front sight will work just fine. Plus, if you ever want to throw a scope on then you can (hunt in a firearms restricted area or in a state that allow scopes on a muzzy).

https://www.eabco.net/PeepRib-Peep-Sights-for-CVA-Optima-Kodiak-Wolf-and-Accura_p_13910.html

On mine I removed the sight that came with the peeprib and put a Williams ghost ring on it.
Not necessarily. I have a CVA optima v2 with a EABCO peep rib and the factory front site is too tall. I have yet to be able to find a shorter front sight. The best I can do is dead on at 50 and no more room for adjustment without a shorter front sight or shimming up the peeprib.


Sent from my iPhone using Tapatalk
Fin,Fur,Feather Taxidermy
Richland, WA
 509-630-8966

Tri-Cities NWTF Chapter President

Offline callturner

  • Trade Count: (+1)
  • Hunter
  • ***
  • Join Date: Jun 2020
  • Posts: 237
  • Location: nine mile falls Washington
    • n/a
  • Groups: nra
Re: Taller front sight
« Reply #23 on: September 25, 2020, 08:42:47 PM »
I use the ebco peep with w Lyman 17A and a tall beaded post insert that came with it  in my CVA . I was shooting 77 weighed gr of blackhorn but bumped it up to 84 and I get about a 2 1/2 in group at 100 yds. That's with a 300 gr Deep Curl in a Harvester crush rib sabot.

Offline riverrun

  • Non-Hunting & Covid-19 Topics
  • Trade Count: (0)
  • Tracker
  • **
  • Join Date: Mar 2010
  • Posts: 83
  • Location: Yakima
Re: Taller front sight
« Reply #24 on: September 25, 2020, 09:28:52 PM »
I had the same issue with needing more rear sight ramp travel. i'm shooting a 300gr. bullet and needed  more travel. found a lower front sight at E.Arthur Brown company which fits cva,traditions and others with a round barrel. I have a cva accura v2 shooting fiber sights and it solved my problem. Part no. 716-66661. Hope this helps!

 


* Advertisement