Question for AR Builders

[lazydrifter]

I bought a DPMS new 3 weeks ago that was stamped 5.56 on the lower and I just bought a new  Colt AR yesterday that is stamped 5.56 on the lower.  I bought 2 PSA stripped receivers earlier this week and they are stamped multi-cal.

[Heredoggydoggy]

That's my thoughts, there is some reason why they have some stamped 5.56 and others stamped multi. All the factory 223's I have bought have always been marked 5.56 on them. So it must have to do with something or every lower out there would be stamped multi.

I think they started stamping them "Multi" when all the other caliber variants in the AR-15 platform became popular.  I have 4 AR-15's and only one is a .223.  When my barrel comes, I'll have 5 AR's and still only have one in .223. 

[grundy53]

I really don't know that I've ever seen a lower not stamped "multi". I've got a factory built rifle and it even says "multi".

You'd probably be dealing with a much older lower if it were stamped with an actual caliber, unless there is some weird reason why they would do that in a ban state maybe.

[carpsniperg2]

Indeed and who knows, there is a reason for it and I am not a legal minded guy. If they have some setup that way there is a reason for it. I don't know the laws but if your weapons got checked out and your gun is registered as a 5.56 only and you have a 6.5 upper on it, then I could see the possiblity of some problems.

There are some funny laws like this and I am not going to pretend to know them. Just some food for thought.

[Heredoggydoggy]

Evidently, It's not an issue.  My 6.8 SPC upper is on a DPMS lower marked "5.56-.223" and when I was checked by the Game Warden when I was deer hunting in 113, His only concern was that I was not hunting with a .223.

[carpsniperg2]

Well that's good to hear. I will be making some calls because I have always wondered and want to hear it for sure.

[Heredoggydoggy]

Yes... but switching mags may be required.

Also with 7.62x39 you'll want to do a lot of research on getting reliable mags as they tend to have feeding issues due to cartridge dimensions.

Just built an upper in 6.5 grendel and will be using the same lower.  Toss in a couple new mags and I was good to go.

Just a word of caution to those of you that are building 6.5 Grendels--make sure you use a Type II bolt.  It's got the same case head diameter, but it's cut 10 thousands" deeper than a 7.62x39 bolt.  Found this out when I built my 20 LBC. (6.5 Grendel necked down to .204)

[Jingles]

Thanks for the info. Sounds like what I am wanting to do is possible

[JohnVH]

My Grendel lower says 5.56

[Blacklab]

here's matches for a ar15 lower multi. 
22
204 ruger
223/5.56x45
5.7x28
223wsm
243wsm
25wsm
6.5 grendel
6.8spc
7.62x39
30AR
450bushmaster
458scocom
50beowulf

[Fisherdave10]

Don't forget .300 Blackout.  I have been very tempted to build one.

I have a friend who got into guns somewhat recently.  He built his second AR as a .300 Blackout (WAS NOT A CHEAP BUILD, we're talking pre-panic prices too) and he has invested a lot into a Lock-n-Load reloading setup.  He is really enthusiastic about it so far.  He has never hunted before and I told him we would hunt this fall.  He's done with his online hunter ed course and is registered for a September field test. 

Hope we can find some deer this fall. 

[Heredoggydoggy]

Don't forget .300 Blackout.  I have been very tempted to build one.

I have a friend who got into guns somewhat recently.  He built his second AR as a .300 Blackout (WAS NOT A CHEAP BUILD, we're talking pre-panic prices too) and he has invested a lot into a Lock-n-Load reloading setup.  He is really enthusiastic about it so far.  He has never hunted before and I told him we would hunt this fall.  He's done with his online hunter ed course and is registered for a September field test. 

Hope we can find some deer this fall.

The 300 Blackout was designed to be a sub-sonic round to be shot in a suppressed rifle so as to be even quieter, since the bullet would not break the sound barrier and make the "crack" like a faster bullet would do.
It's called the 300 Blackout because the person that developed the round called it the 300 Whisper, and trademarked the name so nobody else could use it.

[NoImpactNoIdea]

Ok the first thing to do is admit you don't know all the answers so I'm asking what might be a silly question for some but I Don't know so am asking those that do.
If a person has a complete lower assembly for a 5.56/223 is it possible to switch out the uppers between the 5.56 and say a 6.8 or 7.62 so that 1 lower would be enough for the other uppers so in essence have 3 different calibers to choose from depending on the game being pursued?

The 7.62 will not be the same if it is 7.62X54.  The AK calibers should fit, the magazines are too big for the 308s to fit in the standard lower.