collapse

Advertisement


Author Topic: DIY Arrow Saw  (Read 7176 times)

Offline coonhound

  • Jeff ><>
  • Trade Count: (0)
  • Longhunter
  • *****
  • Join Date: Sep 2007
  • Posts: 687
  • Location: Lewis County
  • Jeff ><>
DIY Arrow Saw
« on: February 15, 2014, 02:52:40 PM »
I made this saw about a year ago, at that time I used a Dremel for the motor.  I just upgraded to a motor I bought from Grainger, it is a nice improvement.  I've got a bit of an advantage over the average Joe with access to a machine shop and sheet metal shop.  It's kind of fun to have a one of a kind tool on your bench.

Jeff

Offline carpsniperg2

  • Site Sponsor
  • Global Moderator
  • Trade Count: (+126)
  • Legend
  • *****
  • Join Date: Sep 2009
  • Posts: 31527
  • Location: Goldendale,WA
Re: DIY Arrow Saw
« Reply #1 on: February 15, 2014, 02:57:12 PM »
Nice looking saw.
Owner: SPLIT DIAMOND TACTICAL
Firearms/Transfers/Parts/Optics
2011 HW Head Competition Winner

Offline MIKEXRAY

  • Trade Count: (0)
  • Sourdough
  • *****
  • Join Date: Jan 2008
  • Posts: 1157
Re: DIY Arrow Saw
« Reply #2 on: February 15, 2014, 03:14:53 PM »
That is a good looking saw .   I watched a hunting TV show and the tip of the week was cutting arrows. It was very informative and they went further then I had seen at my local shop.  They advised to cut both ends as the spine is measured from the center of the shaft from the manufacturer,  then they dropped it in water to see what side of the arrow floated & marked the arrow with a sharpie.  This told them where to fletch and put the finished tip insert as they wanted them lined up.  Would be cool to have the saw all set up and do your own , I think there are some critical steps there for accuracy that I have not taken advantage of.

Offline sled

  • Non-Hunting Topics
  • Trade Count: (0)
  • Frontiersman
  • *****
  • Join Date: Mar 2010
  • Posts: 3559
  • Location: Lake Stevens
Re: DIY Arrow Saw
« Reply #3 on: February 15, 2014, 03:15:50 PM »
 :tup: 

Offline Redbeard

  • Political & Covid-19 Topics
  • Trade Count: (0)
  • Scout
  • ****
  • Join Date: Feb 2013
  • Posts: 272
  • Location: Hanging out somewhere.
  • Groups: NRA
Re: DIY Arrow Saw
« Reply #4 on: February 15, 2014, 04:01:21 PM »
Looks nice.  I have kicked around making one too.

Offline coonhound

  • Jeff ><>
  • Trade Count: (0)
  • Longhunter
  • *****
  • Join Date: Sep 2007
  • Posts: 687
  • Location: Lewis County
  • Jeff ><>
Re: DIY Arrow Saw
« Reply #5 on: February 15, 2014, 04:05:29 PM »
What was your total cost on materials?

About $100, the motor was the major item at about $50.00.  It's a Dayton motor from Grainger however I found this one on E-bay, it's about $100 if you buy it directly from Grainger.  It's the same motor that Apple uses on their saws.

Offline Dnix

  • Trade Count: (0)
  • Pilgrim
  • *
  • Join Date: Dec 2011
  • Posts: 8
  • Location: Puyallup
Re: DIY Arrow Saw
« Reply #6 on: July 27, 2014, 07:09:43 AM »
I can't quite tell how this saw works. Does the motor swing down or slide to cut the arrow? If yes, could you post a picture of the hinge point or slide? Or is all of the movement handled by the front bearing mount while keeping the aluminum angle in contact with the two bolt heads?

Offline coonhound

  • Jeff ><>
  • Trade Count: (0)
  • Longhunter
  • *****
  • Join Date: Sep 2007
  • Posts: 687
  • Location: Lewis County
  • Jeff ><>
Re: DIY Arrow Saw
« Reply #7 on: August 19, 2014, 09:18:54 PM »
There is no hinge point, you simple pivot the arrow onto the bearings and then rotate the arrow to achieve a square cut.  You adjust the angle with the bearings so that the blade slightly cuts through the 1st wall of the arrow.  The 2 bolt heads you mentioned are only there as a guide to keep the angle square when making adjustments to the rollers. This is typical of most saws except they have a shelf rather than a set of rollers. 

 


* Advertisement

* Recent Topics

49 degrees north late Moose tag by vandeman17
[Today at 09:05:21 AM]


Stillaguamish 448 QD rifle tag by jason stevens
[Today at 09:05:09 AM]


Bear behavior by dylan34_36
[Today at 08:51:28 AM]


Idaho Unit 31 Late Rifle! by Sliverslinger
[Today at 08:36:10 AM]


Getting back into dogs by brokentrail
[Today at 08:33:12 AM]


Bow mount trolling motors by GWP
[Today at 08:25:59 AM]


Idaho 2025 Controlled Hunts by Machias
[Today at 08:12:17 AM]


Machias' 2025 Spring Bear/Northern Idaho by Machias
[Today at 07:52:44 AM]


Norway pass Elk by hunterednate
[Today at 07:44:13 AM]


Early controlled hunt rifle tag Lemhi Range by Shooter4
[Today at 07:29:56 AM]


FFL preferences or warnings in Olympia or south Sound area? by Sneaky
[Today at 05:43:56 AM]


Toutle Quality Bull - Rifle by RB
[Today at 03:13:07 AM]


Boat registration by Happy Gilmore
[Yesterday at 10:22:29 PM]


Norway Pass Archery Elk 2025 by Boss .300 winmag
[Yesterday at 09:14:45 PM]


Entiat Quality tag by WAcoueshunter
[Yesterday at 09:05:06 PM]


Palouse/Mica (GMU 127) Access for Trades Work by dr.derek
[Yesterday at 08:29:53 PM]


Pearygin Quality by MADMAX
[Yesterday at 07:55:09 PM]


Teanaway bull elk by Caveman123
[Yesterday at 07:43:44 PM]


Oregon results posted. by Caveman123
[Yesterday at 07:40:47 PM]


2025 Draw Results by Yeti419
[Yesterday at 07:27:32 PM]

SimplePortal 2.3.7 © 2008-2025, SimplePortal