collapse

Advertisement


Author Topic: DIY Arrow Saw  (Read 7160 times)

Offline coonhound

  • Jeff ><>
  • Trade Count: (0)
  • Longhunter
  • *****
  • Join Date: Sep 2007
  • Posts: 687
  • Location: Lewis County
  • Jeff ><>
DIY Arrow Saw
« on: February 15, 2014, 02:52:40 PM »
I made this saw about a year ago, at that time I used a Dremel for the motor.  I just upgraded to a motor I bought from Grainger, it is a nice improvement.  I've got a bit of an advantage over the average Joe with access to a machine shop and sheet metal shop.  It's kind of fun to have a one of a kind tool on your bench.

Jeff

Offline carpsniperg2

  • Site Sponsor
  • Global Moderator
  • Trade Count: (+126)
  • Legend
  • *****
  • Join Date: Sep 2009
  • Posts: 31527
  • Location: Goldendale,WA
Re: DIY Arrow Saw
« Reply #1 on: February 15, 2014, 02:57:12 PM »
Nice looking saw.
Owner: SPLIT DIAMOND TACTICAL
Firearms/Transfers/Parts/Optics
2011 HW Head Competition Winner

Offline MIKEXRAY

  • Trade Count: (0)
  • Sourdough
  • *****
  • Join Date: Jan 2008
  • Posts: 1157
Re: DIY Arrow Saw
« Reply #2 on: February 15, 2014, 03:14:53 PM »
That is a good looking saw .   I watched a hunting TV show and the tip of the week was cutting arrows. It was very informative and they went further then I had seen at my local shop.  They advised to cut both ends as the spine is measured from the center of the shaft from the manufacturer,  then they dropped it in water to see what side of the arrow floated & marked the arrow with a sharpie.  This told them where to fletch and put the finished tip insert as they wanted them lined up.  Would be cool to have the saw all set up and do your own , I think there are some critical steps there for accuracy that I have not taken advantage of.

Offline sled

  • Non-Hunting Topics
  • Trade Count: (0)
  • Frontiersman
  • *****
  • Join Date: Mar 2010
  • Posts: 3559
  • Location: Lake Stevens
Re: DIY Arrow Saw
« Reply #3 on: February 15, 2014, 03:15:50 PM »
 :tup: 

Offline Redbeard

  • Political & Covid-19 Topics
  • Trade Count: (0)
  • Scout
  • ****
  • Join Date: Feb 2013
  • Posts: 272
  • Location: Hanging out somewhere.
  • Groups: NRA
Re: DIY Arrow Saw
« Reply #4 on: February 15, 2014, 04:01:21 PM »
Looks nice.  I have kicked around making one too.

Offline coonhound

  • Jeff ><>
  • Trade Count: (0)
  • Longhunter
  • *****
  • Join Date: Sep 2007
  • Posts: 687
  • Location: Lewis County
  • Jeff ><>
Re: DIY Arrow Saw
« Reply #5 on: February 15, 2014, 04:05:29 PM »
What was your total cost on materials?

About $100, the motor was the major item at about $50.00.  It's a Dayton motor from Grainger however I found this one on E-bay, it's about $100 if you buy it directly from Grainger.  It's the same motor that Apple uses on their saws.

Offline Dnix

  • Trade Count: (0)
  • Pilgrim
  • *
  • Join Date: Dec 2011
  • Posts: 8
  • Location: Puyallup
Re: DIY Arrow Saw
« Reply #6 on: July 27, 2014, 07:09:43 AM »
I can't quite tell how this saw works. Does the motor swing down or slide to cut the arrow? If yes, could you post a picture of the hinge point or slide? Or is all of the movement handled by the front bearing mount while keeping the aluminum angle in contact with the two bolt heads?

Offline coonhound

  • Jeff ><>
  • Trade Count: (0)
  • Longhunter
  • *****
  • Join Date: Sep 2007
  • Posts: 687
  • Location: Lewis County
  • Jeff ><>
Re: DIY Arrow Saw
« Reply #7 on: August 19, 2014, 09:18:54 PM »
There is no hinge point, you simple pivot the arrow onto the bearings and then rotate the arrow to achieve a square cut.  You adjust the angle with the bearings so that the blade slightly cuts through the 1st wall of the arrow.  The 2 bolt heads you mentioned are only there as a guide to keep the angle square when making adjustments to the rollers. This is typical of most saws except they have a shelf rather than a set of rollers. 

 


* Advertisement

* Recent Topics

Stuffed Pork Chop by EnglishSetter
[Today at 11:12:59 PM]


I’m on a blacktail mission by skagitsteel
[Today at 09:45:22 PM]


Another great day in the turkey woods. by Remington Outdoors
[Today at 09:43:57 PM]


Bow mount trolling motors by metlhead
[Today at 09:11:28 PM]


Buck age by kentrek
[Today at 08:56:47 PM]


Oregon special tag info by Judespapa
[Today at 08:37:07 PM]


Eastern WA-WT hunting from tree stands?? by hunter399
[Today at 07:59:18 PM]


Hoof Rot by Dirtnap
[Today at 04:39:37 PM]


Honda BF15A Outboard Problems by CP
[Today at 01:36:59 PM]


Anybody breeding meat rabbit? by HighlandLofts
[Today at 12:01:17 PM]


where is everyone? by nwwanderer
[Today at 11:12:50 AM]


Get ready for the 4th of July by rosscrazyelk
[Today at 09:36:56 AM]


Unknown Suppressors - Whisper Pickle by Karl Blanchard
[Today at 09:15:32 AM]


Wolf documentary PBS by Boss .300 winmag
[Today at 09:09:55 AM]


Idaho Mt goat draft plan by time2hunt
[Today at 07:59:04 AM]


Cougar Problems Toroda Creek Road Near Bodie by Elkaholic daWg
[Today at 07:52:17 AM]


Disabled Fishing License by Blacklab
[Today at 07:44:43 AM]


Ever win the WDFW Big Game Raffle? by jackelope
[Today at 07:18:59 AM]


Missoula Fishing by borntoslay
[Yesterday at 11:30:10 PM]


Iceberg shrimp closed by Tbar
[Yesterday at 10:55:37 PM]

SimplePortal 2.3.7 © 2008-2025, SimplePortal