collapse

Advertisement


Author Topic: Need some carb work, anyone help?  (Read 5367 times)

Offline Smossy

  • Illiterate Woodsman
  • Past Sponsor
  • Trade Count: (+1)
  • Old Salt
  • *****
  • Join Date: Jan 2013
  • Posts: 6668
  • Location: Spanaway, Wa
  • Slow down and enjoy the moment.
Need some carb work, anyone help?
« on: October 04, 2014, 05:10:30 PM »
Ok I'm just not willing to drop the $300-700 on carburetor work and maintenance from a dealer just to get our ATVs running. We have 2 that are basically brand new and have been sitting for close to 3-4 years with the same gas/oil fluids in them since then, neither vehicle will fire up at this point.
One is a 2005 Suzuki Eager 400 and the other is a Suzuki Ozark 250
The smaller of the 2 / the Ozark.. ran for a week and I ran it pretty hard just trying to see what it was capable of, eventually it started to backfire and bog down then just all together not start.
The Eiger will fire up for a split second if you spray started fluid into where the air filter is but just will not last.

My question to you all is first, anyone have any ideas what the main problem may be? I'm thinking bunked up crabs from years old gas...
Second, is there anyone who knows enough about these things to be willing to take on the task of helping me get them running. I'm willing to pay and work out deals. Preferably someone semi local.
One touch of nature makes the whole world kin.

Offline WA hunter14

  • Trade Count: (0)
  • Longhunter
  • *****
  • Join Date: May 2011
  • Posts: 851
  • Location: Weippe ID
Re: Need some carb work, anyone help?
« Reply #1 on: October 04, 2014, 05:13:10 PM »
try all new gas in both plus some fuel injector cleaner and new spark plugs and i bet you will be fine

Offline Smossy

  • Illiterate Woodsman
  • Past Sponsor
  • Trade Count: (+1)
  • Old Salt
  • *****
  • Join Date: Jan 2013
  • Posts: 6668
  • Location: Spanaway, Wa
  • Slow down and enjoy the moment.
Re: Need some carb work, anyone help?
« Reply #2 on: October 04, 2014, 05:16:18 PM »
try all new gas in both plus some fuel injector cleaner and new spark plugs and i bet you will be fine
I'll give it a try, do I just siphon out the old gas?
One touch of nature makes the whole world kin.

Offline WA hunter14

  • Trade Count: (0)
  • Longhunter
  • *****
  • Join Date: May 2011
  • Posts: 851
  • Location: Weippe ID
Re: Need some carb work, anyone help?
« Reply #3 on: October 04, 2014, 05:20:14 PM »
probably the best way to go yea

Offline cooltimber

  • Trade Count: (+1)
  • Longhunter
  • *****
  • Join Date: Sep 2011
  • Posts: 593
  • Location: Idaho
Re: Need some carb work, anyone help?
« Reply #4 on: October 04, 2014, 05:20:52 PM »
Hi if I lived closer I'd do 4 free,but it's simple,just pay attention .remove carbs,take the bottom bowl off and u will c the main jet,it has a hole in it..next take out the emulsion tube.this will b clogged,take a wire and clean out the hole's,this is behind the main jet which u just took out.your idler jets or primary jets need to be taken out and cleaned,count out the turns.when you replace them count those turns,then back out one full turn,no more. if carb is very dirty,boil in water and lemon juice for couple hr's..I had to do this in camp with a buddies quad that forgot to,run carb out of gas before he stored it...pm me will b ok
rvn 69-70 11 b 2p 173rd
rmef
  2 ways to conquer and enslave a nation
      one's by sword,the other is by debt.
               John Adams

Offline WA hunter14

  • Trade Count: (0)
  • Longhunter
  • *****
  • Join Date: May 2011
  • Posts: 851
  • Location: Weippe ID
Re: Need some carb work, anyone help?
« Reply #5 on: October 04, 2014, 05:27:40 PM »
i would agree that the one that ran then died might have a gunked up carb but i have never had gas last that long. try looking at some videos on youtube of cleaning small engine carb. if you have to or decide to clean the carbs get some carb cleaner from a place like napa

Offline Smossy

  • Illiterate Woodsman
  • Past Sponsor
  • Trade Count: (+1)
  • Old Salt
  • *****
  • Join Date: Jan 2013
  • Posts: 6668
  • Location: Spanaway, Wa
  • Slow down and enjoy the moment.
Re: Need some carb work, anyone help?
« Reply #6 on: October 04, 2014, 05:33:55 PM »
i would agree that the one that ran then died might have a gunked up carb but i have never had gas last that long. try looking at some videos on youtube of cleaning small engine carb. if you have to or decide to clean the carbs get some carb cleaner from a place like napa
It was only about an hour a day for like 4 days, may not be as hard as I made it sound. Some guys do that Ina day.
One touch of nature makes the whole world kin.

Offline WA hunter14

  • Trade Count: (0)
  • Longhunter
  • *****
  • Join Date: May 2011
  • Posts: 851
  • Location: Weippe ID
Re: Need some carb work, anyone help?
« Reply #7 on: October 04, 2014, 05:38:55 PM »
did the one that backfired and quite blow out a bunch of smoke?

Offline Smossy

  • Illiterate Woodsman
  • Past Sponsor
  • Trade Count: (+1)
  • Old Salt
  • *****
  • Join Date: Jan 2013
  • Posts: 6668
  • Location: Spanaway, Wa
  • Slow down and enjoy the moment.
Re: Need some carb work, anyone help?
« Reply #8 on: October 04, 2014, 05:59:08 PM »
did the one that backfired and quite blow out a bunch of smoke?
not that I noticed, I was riding it full throttle quite a bit then I started to get sputtering, then a few backfires, the. It bogged down and died. No smoke (again that I noticed) no smell, no obvious reasons.
One touch of nature makes the whole world kin.

Offline WA hunter14

  • Trade Count: (0)
  • Longhunter
  • *****
  • Join Date: May 2011
  • Posts: 851
  • Location: Weippe ID
Re: Need some carb work, anyone help?
« Reply #9 on: October 04, 2014, 06:07:44 PM »
you would have noticed this amount of smoke  :chuckle: 

If you want to get the thing up and running now then you should just put new gas in them and make sure plugs arent fouled then(and the gas is turned on).

If you want to give them a more long term service or are getting ready to use them alot like for hunting season then i would get new spugs, new fuel filters, new gas, change oil, take carbs off and clean them really well.

off the top of my head that is what i would do once you get into it you may realize you donnt need to do some of them or that you need to do more.

Offline Rick

  • Non-Hunting Topics
  • Trade Count: (0)
  • Sourdough
  • *****
  • Join Date: Dec 2007
  • Posts: 1858
  • Location: Everett
Re: Need some carb work, anyone help?
« Reply #10 on: October 04, 2014, 07:34:27 PM »
Carbs aren't voodoo. I'll bet a 30 second search on Youtube will have you well on your way to fixing them yourself.

Offline Weehunt66

  • Trade Count: (+1)
  • Hunter
  • ***
  • Join Date: Sep 2010
  • Posts: 123
  • Location: Cowiche
  • Groups: RMEF, NRA
Re: Need some carb work, anyone help?
« Reply #11 on: October 04, 2014, 07:42:58 PM »
Replace your fuel filters.

Offline wildmanoutdoors

  • Trade Count: (0)
  • Sourdough
  • *****
  • Join Date: Jul 2009
  • Posts: 2459
  • Location: Port Orchard
Re: Need some carb work, anyone help?
« Reply #12 on: October 15, 2014, 01:33:34 PM »

The one that starts with a shot of fluid is a piece of cake. Remove and clean carb. Put back together with new fuel.

The other, since it ran, then died could be a multi tude of things. Id start by replacing plug and cleaning carb.

How many porcinins could I get in pay to get them going?

Offline Smossy

  • Illiterate Woodsman
  • Past Sponsor
  • Trade Count: (+1)
  • Old Salt
  • *****
  • Join Date: Jan 2013
  • Posts: 6668
  • Location: Spanaway, Wa
  • Slow down and enjoy the moment.
Re: Need some carb work, anyone help?
« Reply #13 on: October 15, 2014, 08:19:13 PM »

The one that starts with a shot of fluid is a piece of cake. Remove and clean carb. Put back together with new fuel.

The other, since it ran, then died could be a multi tude of things. Id start by replacing plug and cleaning carb.

How many porcinins could I get in pay to get them going?
Lol id have to talk the the boss
One touch of nature makes the whole world kin.

Offline bone collector 12

  • Non-Hunting Topics
  • Trade Count: (0)
  • Scout
  • ****
  • Join Date: Oct 2011
  • Posts: 379
  • Location: quincy wa
Re: Need some carb work, anyone help?
« Reply #14 on: October 15, 2014, 08:22:26 PM »
Spark plugs and new fuel also try running some SEA FOAM additive threw it

 


* Advertisement

* Recent Topics

Looking for italian sausage recipe by emac
[Yesterday at 10:44:24 PM]


Good day of steelhead fishing! by Mfowl
[Yesterday at 10:21:20 PM]


2025 Area 9 King Opener by Mfowl
[Yesterday at 10:19:48 PM]


Pocket Carry by hookr88
[Yesterday at 10:02:24 PM]


A little Martini Cadet varmint rifle I have been working on by JDHasty
[Yesterday at 08:26:39 PM]


AKC lab puppies! Born 06/10/2025 follow as they grow!!! by scottfrick
[Yesterday at 07:39:21 PM]


Triple Blacktail Pedestal by blackveltbowhunter
[Yesterday at 05:35:41 PM]


Mt. St. Helens Goat by CNELK
[Yesterday at 05:05:47 PM]


Tasty Pinks! by pianoman9701
[Yesterday at 04:16:01 PM]


49 Degrees North Early Bull Moose by Kdog
[Yesterday at 03:06:42 PM]


2024 DFW Wolf report by Kales15
[Yesterday at 02:13:59 PM]


Boundary Waters walleye trip by jackelope
[Yesterday at 02:13:36 PM]


Area 11 2025 - Well? by Crunchy
[Yesterday at 02:01:11 PM]


Rock creek gone? Next? by JasonG
[Yesterday at 11:13:02 AM]


Surprise quality deer tag by jwesterback
[Yesterday at 10:01:53 AM]


EAA Girsan Witness 2311 in 10mm with factory red dot, lightly used. by Dirty Dingus Dave
[Yesterday at 08:51:01 AM]


North Sea Fishing trip by Machias
[Yesterday at 07:55:34 AM]


Looking for Solid 22 LR input by JDHasty
[July 18, 2025, 09:18:47 PM]


506 Willapa Hills Late Season Antlerless Tag by stur4351@gmail.com
[July 18, 2025, 08:37:32 PM]


William o Douglas lakes by JWBINX
[July 18, 2025, 06:02:09 PM]

SimplePortal 2.3.7 © 2008-2025, SimplePortal