Reloading 9mm and .40 S&W

[jmkuhlman]

I'm just beginning to load these rounds and would like some advice on loads.  I'm planning to use Bullseye powder and Remington brass, but haven't picked a bullet yet.  I'll also be using CCI small pistol primers.  I'm leaning towards jacketed hollow points, but I'm open to what others are using and recommend.  I've researched Speer, Hornady, and Nosler a little bit and can't quite decide.  Thanks for sharing.   

[huntnphool]

Are these for target shooting or self defense?

[wrangler]

not to hijack your thread but does anyone else load wad cutters seated upsidedown, for the bedside 9mm? hehe, the perfect burgler load!

[actionshooter]

Thats a pretty good choice of bullets and primers. I like hornady XTPs for self defense, I've always been partial to winchester brass and I don't care for for Bullseye. Its good powder but very dirty. For .40 I use N340, Vihtivouri (sp?)

[jmkuhlman]

Looking for target and self defense. 

[jmkuhlman]

Just curious, why do you perfer Winchester brass?  I have used Winchester brass for my rifle cartridges and perfer Remington.  I may have had a bad bag, but I had 5 or 6 rounds split above the neck while resizing a bag of Winchester.  I just chose to stay clear of it, but maybe I was doing something wrong.  I was resizing 25-06 and never had problems with Remington.  Thoughts?

Thanks for the heads up on Bullseye.  My reloading manual lists Bullseye as being one of the most accurate powders for both loads.  What grain bullets are you using in your .40?  I was looking 170-180.

[norsepeak]

I've got about 800 rounds of 9mm if want to shoot them and then use the brass.  $250 for all.

[jmkuhlman]

Sent you a PM norsepeak.

[tlbradford]

I have a .40 load that is very reliable for my Beretta 96.  What are you shooting, and what is the barrel length?  Bullseye shooting or IPSC?

[jmkuhlman]

H&K Compact with a 3.58 inch barrel.  Bullseye and IPSC shooting, but primarily IPSC.  I'm OK if I need two completely different loads.

[gasman]

I have a .40 load that is very reliable for my Beretta 96.  What are you shooting, and what is the barrel length?  Bullseye shooting or IPSC?

What is you recipe for for your .40 Beretta 96.
I am going tostar loading for mine and would like to here of a good recipe, or a place to start.



Pete

[12Gauge]

For the 9mm I use the 125 grain lead .356 diameter with 4.3 grains of Unique for target practice.  It burns dirty because of the lube on the lead and partly unique burns dirty. 

Sometimes I use the Magtech or Rainier lead safe bullets bulk from MidwayUSA, 124grain.  They are about $94 per 1000 + shipping.  with Winchester 231 , 4.5 grains it burns a little cleaner than the unique.

[jmkuhlman]

Thanks 12Gauge, Winchester 231 was one of the powders I was looking at also. 

What brand are you using for your 125 grain bullet?  This is the weight I was planing to use, so it appears I'm heading in the right direction. 

[actionshooter]

Just curious, why do you perfer Winchester brass?  I have used Winchester brass for my rifle cartridges and perfer Remington.  I may have had a bad bag, but I had 5 or 6 rounds split above the neck while resizing a bag of Winchester.  I just chose to stay clear of it, but maybe I was doing something wrong.  I was resizing 25-06 and never had problems with Remington.  Thoughts?

Thanks for the heads up on Bullseye.  My reloading manual lists Bullseye as being one of the most accurate powders for both loads.  What grain bullets are you using in your .40?  I was looking 170-180.

Winchester brass doesn't stretch the way Remington brass does. It takes longer to wear it out, and it seems to be more consistent. I have Winchester .45acp  brass which has been loaded dozen times, the Remington would never make it that long under heavy loads.

[jmkuhlman]

Do you experience this with rifle brass as well?