collapse

Advertisement


Author Topic: new barrel, any suggestions?  (Read 1915 times)

Offline bow-n-head

  • Trade Count: (0)
  • Longhunter
  • *****
  • Join Date: Jan 2009
  • Posts: 533
new barrel, any suggestions?
« on: March 27, 2009, 05:21:56 PM »
I have a 300 H&H in a winchester 70. I think the headspace is streached and need to put a new barrel on it. The problem I see is the new barrel is going to cost more than the gun did to begin with. Does this sound right to any of you?

Offline mossback91

  • Political & Covid-19 Topics
  • Trade Count: (+3)
  • Frontiersman
  • *****
  • Join Date: Dec 2007
  • Posts: 3195
Re: new barrel, any suggestions?
« Reply #1 on: March 27, 2009, 05:23:02 PM »
how long ago did you buy the rifle?

Offline AWS

  • Trade Count: (+2)
  • Sourdough
  • *****
  • Join Date: Dec 2007
  • Posts: 1838
Re: new barrel, any suggestions?
« Reply #2 on: March 27, 2009, 05:42:52 PM »
It's pretty hard to change the headspace on a bolt gun by shooting it even if you overload it alot especially a modern arm like a Mod 70.  I would spend a couple of bucks and get a headspace gauge (field guage).  Unless you've cleaned it to death a 300H&H will not wear out a barrel in less than a couple of thousand rounds.  If it is really a headspace problem and your rifleling is still good you can have the barrel set back a turn and rechamber the barrel.

As far as a new barrel you can figure $400 to $600+ to buy a new barrel and have it installed.

Why do you feel you have a head space problem?

It is easy to over size(if your a reloader) magnum brass as it headspaces on the belt and it is easy to set the shoulder back too far.  Backing off your sizing die a little will stop case head seperations.

AWS
After the first shot the rest are just noise.

Make mine a Minaska

Offline AWS

  • Trade Count: (+2)
  • Sourdough
  • *****
  • Join Date: Dec 2007
  • Posts: 1838
Re: new barrel, any suggestions?
« Reply #3 on: March 27, 2009, 05:51:15 PM »
Are these factory loads or new brass reloads?

AWS
After the first shot the rest are just noise.

Make mine a Minaska

Offline AWS

  • Trade Count: (+2)
  • Sourdough
  • *****
  • Join Date: Dec 2007
  • Posts: 1838
Re: new barrel, any suggestions?
« Reply #4 on: March 27, 2009, 06:00:36 PM »
Just run your new brass into your sizing die enough that it only sizes half way down the neck, a little soot from a candle on the neck will show you.   It sounds like your setting the shoulder back.   

AWS
After the first shot the rest are just noise.

Make mine a Minaska

Offline AWS

  • Trade Count: (+2)
  • Sourdough
  • *****
  • Join Date: Dec 2007
  • Posts: 1838
Re: new barrel, any suggestions?
« Reply #5 on: March 27, 2009, 06:55:05 PM »
Sorry for the delay, had to go to dinner.   

If you don't have any problems with the partially sized case then you can size the once fired cases just enough to barely touch the shoulder, again using soot on the nack and shoulder to tell you how fare you are going into your sizing die.

AWS

After the first shot the rest are just noise.

Make mine a Minaska

Offline Huntbear

  • I am a BAD Kitteh
  • Washington For Wildlife
  • Trade Count: (0)
  • Old Salt
  • ******
  • Join Date: Nov 2007
  • Posts: 9616
  • Location: Wandering Lost East of the Mountains
  • Y.A.R. Jester aka Smart Ass
    • http://www.facebook.com/profile.php?id=1236486665
Re: new barrel, any suggestions?
« Reply #6 on: March 27, 2009, 07:26:58 PM »
Exactly why I only neck size all my magnum cases. 
By my honorable conduct as a hunter let me give a good example and teach new hunters principles of honor, so that each new generation can show respect for their god, other hunters and the animals, and enjoy the dignity of the hunt.

Calling an illegal alien an 'undocumented immigrant' is like calling a drug dealer an 'unlicensed pharmacist'.

 


* Advertisement

* Recent Topics

Norway pass Elk by moocher97
[Today at 12:11:05 AM]


Toutle Quality Bull - Rifle by moocher97
[Today at 12:00:21 AM]


NEED ADVICE: LATE after JUNE 15th IDAHO BEAR by huntnnw
[Yesterday at 11:20:59 PM]


Mature bulls during late season? by Dark2Dark
[Yesterday at 10:53:27 PM]


Cowiche Unit 368 by Limhangerslayer
[Yesterday at 10:41:37 PM]


2025 Draw Results by duckmen1
[Yesterday at 10:30:36 PM]


Put in for a tag I NEVER thought I would draw. by elkrack
[Yesterday at 10:15:14 PM]


Awesome customer service by deerlick
[Yesterday at 10:13:19 PM]


Commercial crab pots going in today. by Stein
[Yesterday at 09:37:31 PM]


FFL preferences or warnings in Olympia or south Sound area? by ASHQUACK
[Yesterday at 09:34:36 PM]


Boat registration by Stein
[Yesterday at 09:31:52 PM]


Flatlanders coming west in 2024, any WA mule deer outfitter recommendations by Beastmonger1987
[Yesterday at 09:31:21 PM]


2024 deer. Let’s see um! by Beastmonger1987
[Yesterday at 09:11:35 PM]


Muzzy Mission Quality!!! by crabcreekhunter
[Yesterday at 09:11:30 PM]


Unknown Suppressors - Whisper Pickle by xrangerx
[Yesterday at 09:06:49 PM]


Stillaguamish 448 QD rifle tag by Bo_nimrod
[Yesterday at 09:03:46 PM]


Nevada mule deer in the rut, followed by late rifle elk in Arizona by Beastmonger1987
[Yesterday at 08:36:20 PM]


Teanaway bull elk by 1buckdown
[Yesterday at 08:34:43 PM]


Colockum Archery Bull Tag by oldleclercrd
[Yesterday at 08:31:58 PM]


2025 OILS! by Buzzsaw461
[Yesterday at 08:17:27 PM]

SimplePortal 2.3.7 © 2008-2025, SimplePortal