collapse

Advertisement


Author Topic: Latest project for 2020  (Read 1945 times)

Offline kselkhunter

  • Trade Count: (0)
  • Sourdough
  • *****
  • Join Date: Jun 2014
  • Posts: 1630
  • Location: United States
Latest project for 2020
« on: March 10, 2020, 03:29:17 PM »
Thought I'd share my latest project work.  Refinishing/refurbishing a Marlin 336W.  Instead of sending off to a gunsmith like prior projects, this is my first attempt at doing any real quasi-gunsmithing myself.   Thought I'd share current progress for those considering doing some work themselves on rifles.  Here are the project details:
  • Marlin 336W in 30-30 purchased 15 years ago new at a gun show in Portland a for special price deal. No real collector value, just a cheap entry level lever gun.   Hunted with it for a few years and harvested a nice 4x4 buck with it. Otherwise carry it for scouting trips or sometimes when hunting really thick wet side areas.  I find myself carrying it more often these days.

    2019 I had it rebored to 356 Winchester by JES Reboring (who had done my 35 Whelen a few years prior).   It's quite accurate with 220gr Speer Hot Cors.  I'll be testing loads soon for some 250gr Hawk bullets and 250gr Kodiak bullets based on some load data from guys I trust that already load those.

    2020 I decided to do my own Duracoat job on it rather than paying a gunsmith to Cerakote.  I purchased a couple of cans of Lauer's aerosol based Duracoat with the hardener already inside, the new "Bad Ass" model they introduced this year. 

    I also decided to change out the furniture.  I bought Ranger Point Precision's buttstock and forend, as well as their flyweight load gate and magazine tube.  The four component swap-out reduces my rifle weight by 1.2lbs.  And the built-in recoil pad on RPPs Buttstock is quite nice.  My 336W original factory buttstock didn't have a recoil pad, just that hard butt pad and it was fine shooting 356W loads as it was so I should be fine with this new buttstock and pad to help absorb the extra recoil from the rifle being lighter.  I'm still waiting for RPP to finish their 35 Rem ammo Quiver design, as I plan to put that on the M-Lok forend slots.  RPP's engineers tell me the rear attach area is too tight for 356W case so I'll have to do some sanding.   


Attached is a photo of the test fitting of the RPP parts (noting I didn't bother putting the lever and other parts back in for the test fitting).  Next up is de-greasing, masking, and Duracoating all the exterior metal parts the next few evenings.  With all the screw holes in the receiver of these Marlins, I'm not looking forward to the masking part tonight.  Going to be getting creative with some q-tips, tape, etc. for all those screw holes.  I bought a couple cans of Duracoat just in case, so will clean and degrease a few other guns to be ready to Duracoat with any excess in the cans while the Duracoat is still good.   


I'll post up a photo when I'm done of the finished product. Duracoat dries in an hour, but takes 2-3 weeks to fully harden, and I plan to wait to do final assembly for a few weeks.  With the weight savings from the RPP components, I'll be right around 6lbs for a 356W carry rifle with the Burris FastFire 3 site when all is done.   


Challenges thus far:  I admit to not being much of a gunsmith, and managed to strip the head of that darn rear barrel band screw upon disassembly.  For those interested, the Irwin screw removal tools work quite well.  The RPP stock comes with it's own barrel band design, so I could have cut through the barrel band had I needed to but was impressed with how easily that Irwin tool took that screw out.   Other than that I'd never completely disassembled the Marlin 100% before, just enough for cleaning previously, so that was an experience.   I made sure to put every part in a Ziploc bag with a label on it so I didn't mix one of the many screws for the wrong part.   My workbench looks like somebody with bad obsessive-compulsive-disorder (well that plus all my organizers on the peg board).  :-)   Other than the stripped screw so far the project has gone well.   I'm impressed with how well the RPP buttstock and forend fit, definitely liking their products.   

Offline kselkhunter

  • Trade Count: (0)
  • Sourdough
  • *****
  • Join Date: Jun 2014
  • Posts: 1630
  • Location: United States
Re: Latest project for 2020
« Reply #1 on: March 10, 2020, 08:23:32 PM »
Here's a photo of the barrel Duracoated after tonight's work. One can was enough to put 3 coats on all the Marlin parts, my over/under barrel, and my buddies single action shotgun barrel.  So am going through his inventory to see what 2-3 guns to use the second can of Duracoat on. 

Going to let the Duracoat harden further before attempting final assembly in a few weeks. Overall happy with it, except one spot I had an error on and had to fix. The shotguns were much easier. Less to mask off.

Offline kselkhunter

  • Trade Count: (0)
  • Sourdough
  • *****
  • Join Date: Jun 2014
  • Posts: 1630
  • Location: United States
Re: Latest project for 2020
« Reply #2 on: March 11, 2020, 08:56:17 PM »
I opted to do a quick assembly to check fit on everything now that the Duracoat finished the initial cure process.   Photo attached.   Not the best lighting for the photo unfortunately. It's Matte Black color of Duracoat on all exterior metal parts. I got the wrong parts for the barrel band attachment for the RPP forend, and the replacements will be here Friday and then I'll be "done" once I Duracoat those and install.


I'm at 5lbs 15oz as it sits. Figure with that barrel band and the mag cap will take me to around 6lb 2oz including the Burris sight. Which I'm happy with the weight reduction given how much I carry this rifle. The Duracoat will continue to fully harden over the next 2-3 weeks.


The can of Duracoat was $56 for the "Bad Ass" model, and that one can was able to put 3 coats on all the exterior metal parts of this rifle and 3 coats each on two shotgun barrels (that had seen better days). When I had my bolt rifle Cerakoted by a gunsmith a few years back it cost $300, and I figure the Marlin would have cost similar, or possibly more because of the additional parts and prep involved. So figure I saved myself at least $250 by doing the Duracoat myself. 


Next up after installing the proper barrel band will be testing the 250gr Hawk and 250gr Kodiak bullet loads.   

Offline Jason

  • Political & Covid-19 Topics
  • Trade Count: (+4)
  • Frontiersman
  • *****
  • Join Date: Jun 2008
  • Posts: 3561
  • Location: Kalama
Re: Latest project for 2020
« Reply #3 on: March 11, 2020, 09:29:10 PM »
Lookin great  :tup:. I have a couple rifles I’m getting ready to Duracoat. After duracoating my rifle last year I let it cure for 6 weeks.

Offline kselkhunter

  • Trade Count: (0)
  • Sourdough
  • *****
  • Join Date: Jun 2014
  • Posts: 1630
  • Location: United States
Re: Latest project for 2020
« Reply #4 on: March 11, 2020, 09:35:46 PM »
Lookin great  :tup:. I have a couple rifles I’m getting ready to Duracoat. After duracoating my rifle last year I let it cure for 6 weeks.

Yeah my plan was to wait 2-3 weeks to let it cure more before attempting a test assembly.  But paranoia set in.  I was so worried about whether I masked off all the screw thread holes properly as I was in a bit of a rush when I did it due to a pending trip I had to get on.  Waiting weeks was going to drive me crazy.  But, turned out fine.  Whew.  Now to let the parts properly cure for awhile. 
« Last Edit: March 11, 2020, 09:45:28 PM by kselkhunter »

Offline kselkhunter

  • Trade Count: (0)
  • Sourdough
  • *****
  • Join Date: Jun 2014
  • Posts: 1630
  • Location: United States
Re: Latest project for 2020
« Reply #5 on: March 13, 2020, 08:47:07 PM »
Final photo now that I got the proper hardware.  Came in at exactly 6lbs.

I used the remaining Duracoat, and spare unused can to coat my over/under, my buddies single shot, my buddies Rem 700, and his Rem 788.  Going to wait 4 weeks to put his Rem 700/788s back together so the Duracoat is fully cured.  Adjusted his triggers to lighter pulls they were way too high. Next up is to glass bed the Rem 700/788 actions once the barrels are ready. 

Offline jasnt

  • ELR junkie
  • Political & Covid-19 Topics
  • Trade Count: (+5)
  • Old Salt
  • ******
  • Join Date: Feb 2010
  • Posts: 6539
  • Location: deer park
  • Out shooting
  • Groups: WSTA
Re: Latest project for 2020
« Reply #6 on: March 14, 2020, 07:43:17 AM »
Looks good
https://www.howlforwildlife.org/take_action  It takes 10 seconds and it’s free. To easy to make an excuse not to make your voice heard!!!!!!

The commission shall attempt to maximize the public recreational game fishing and hunting opportunities of all citizens, including juvenile, disabled, and senior citizens.
https://apps.leg.wa.gov/RCW/default.aspx?cite=77.04.012

Offline zwickeyman

  • Past Sponsor
  • Trade Count: (+23)
  • Sourdough
  • *****
  • Join Date: Nov 2014
  • Posts: 1746
  • Location: Victor Idaho
Re: Latest project for 2020
« Reply #7 on: March 14, 2020, 08:11:47 AM »
Going to a great brush gun, looks good
The mountains are calling and I must go

 


* Advertisement

* Recent Topics

11th Annual 'Pull For Scouting' Clay Crushing Classic by high_hunter
[Today at 12:27:18 AM]


AKC lab puppies! Born 06/10/2025 follow as they grow!!! by high_hunter
[Today at 12:21:33 AM]


Ritzville Rifle Buck - GMU 284 by high_hunter
[Yesterday at 11:49:16 PM]


Antlerless Moose more than once? by shootem
[Yesterday at 11:25:51 PM]


Nooksack Muzzleloader Bull Tag by high_hunter
[Yesterday at 10:42:24 PM]


2025 Draw Results by kramman
[Yesterday at 10:27:20 PM]


My wife drew quality deer DESERT rifle 10/18-10/26!!!!! by high_hunter
[Yesterday at 10:17:15 PM]


Palouse buck deer by blumtnelkndeer
[Yesterday at 10:14:00 PM]


Drew Quality by Jimmer
[Yesterday at 09:34:00 PM]


Nevada guide draw Mule Deer by Beastmonger1987
[Yesterday at 09:33:34 PM]


Quality Swakane by Rainier10
[Yesterday at 09:09:17 PM]


Son drawn - Silver Dollar Youth Any Elk - Help? by VickGar
[Yesterday at 09:06:22 PM]


Observatory quality bull rifle by buglebuster
[Yesterday at 09:00:02 PM]


Anterless 1334 muzzle loader by Bdawg
[Yesterday at 08:46:31 PM]


A little Martini Cadet varmint rifle I have been working on by JDHasty
[Yesterday at 08:43:33 PM]


Pogue Quality by geauxtigers
[Yesterday at 08:38:35 PM]


Bow mount trolling motors by Happy Gilmore
[Yesterday at 08:06:18 PM]


2025 OILS! by HUNTNORTHWEST
[Yesterday at 07:46:27 PM]


A question for any FFL holders on here by Knocker of rocks
[Yesterday at 07:34:49 PM]


Last year putting in… by MADMAX
[Yesterday at 07:25:41 PM]

SimplePortal 2.3.7 © 2008-2025, SimplePortal