Downrigger Location on Small Boats

[pickardjw]

Hoping to get some insight on where everyone puts their downriggers on smaller aluminum boats. I have a 14' and am thinking about mounting them behind the rear bench on a deck/platform.

Disadvantages: I'm the only one reeling, lines will be harder to reach (will be adding swivel bases to make that easier and gain some height), less of a chance of seeing the balls on my depth finder.
Advantages : they are out of the way maintaining my deck space (no middle bench), mounting structure will be sufficiently strong


I do see a lot of people mounting them more towards the middle of the boat though. Given that I don't have a middle bench, this may be tougher for me and I'd likely need to mount them on a 2x6 that spans between the gunwhales. Or build some kind of right angle mounts that secure down to my deck.

Disadvantages: takes up deck space, restricts walkthough access with 2x6 option, right angle bracket option could have strength concerns
Advantages : more balanced position weight wise, more likely to see balls on depth finder, two person reel access, better access to lines.


Where are your downriggers on your small boat?

[Angry Perch]

Do you already have the downriggers? There are quite a few available that clamp on, eliminating the need for a mount as you describe.

[BigGoonTuna]

Auburn sports and marine sells bolt on downrigger mounting brackets, if you’re not afraid of drilling holes. I had one on my old smoker craft and it worked well.

[pickardjw]

Yep, got some Penn Fathomaster 600's with the 2' booms. I think the gunwales are too thin to support the forces a downrigger will put on them, especially in the middle of the boat where there's no bench support between thim. It's a typical riveted aluminum utility boat so they already vibrate a lot under idle. Not heavy gauge material.

[Stein]

I had a 14' smokercraft and mounted them over the rear seat, simply because it was easiest to build a mount there than anywhere else.

I don't think it matters much, you get used to where they are.

[kenzmad]

Imagine hooking a crab pot. Do you want it to roll the boat? As far aft as practicable is best. Harder to drag the stern under than it is to tip a small boat over.

[curtmdavis]

This how I rigged mine. Clamps that attach to the gunnel, and some AL plate. The turn buckles provide the support.

[curtmdavis]

 One is toward the back, one more forward. Hung up my DR balls on stumps a few times. Never tipped, only turns me abruptly. 
 In this image there both pretty far back.

[GWP]

My small boat is even worse as it is a foldable (soft sides, plastic) PortaBote. Seat attachment and or cross bar options were considered, but just ended up using a Dipsy Diver for now. My pole holders are clamp on and work well, but I don’t think they will take a lot of strain.
I will probably build a cross bar in the back and use that for a downrigger mount at some point, as I want to reinforce the transom, but for now I will use Divers.

[pickardjw]

Went with a mount behind the rear bench on a platform that connects the bench to the transom. Worked great today. Only had one mounted though, baseplate for the second comes in Monday. Will update with pics later.

[lokidog]

Mount forward enough to easily access your downrigger clips and you don't want to have to lean back to the transom to real them up. Also, too far back and they will act like the vane of an arrow trying to keep the boat going in a straight line... experienced that.

[pickardjw]

It was definitely harder to turn to port (downrigger was on starboard). Tiller drive made it a little easier to overcome. I can reach the clip from my seat and reel from it pretty comfortably too. The port side will be more interesting for that. Will definitely have to stand up to get over to the clip, hoping I can reach the crank though.

Got my second mounting bracket in the mail today but doing a bear hunt tomorrow. Hope to get everything in place Monday.

[pickardjw]

Dry fit for the port downrigger went well, looks like I can reel and deploy from my seat on that one too. Only need to stand up to reach the clip.

At 1-1.3 MPH with an 8lb ball I can track them on my sonar down to about 50' and I lose them due to blowback after that. Didn't want to go too heavy on the ball in a small boat but maybe it's less of an issue than I'm assuming.

Overall I'm happy with the placement right now. Going to hit Chelan for Kokes and Macks this weekend and then Alta Mon-Tue for Kokes. That will be the true test, particularly the Macks.

[pickardjw]

With pics

[Stein]

For your releases, run them on 6' (or even more) of 150ish pound mono.  Then, get a broom stick, cut the broom off and screw in an open eye hook.  Use that to grab the mono from the release and you don't have to lean over.