collapse

Advertisement


Author Topic: Barrel threading for suppressor question  (Read 1475 times)

Offline raydog

  • Trade Count: (+4)
  • Longhunter
  • *****
  • Join Date: Nov 2012
  • Posts: 782
  • Location: Wetside
  • Groups: RMEF
Barrel threading for suppressor question
« on: November 29, 2022, 04:59:59 PM »
I recently purchased my first suppressor and I'm wanting to thread a Tikka 7mm rem mag superlite for the suppressor I purchased. I don't actually have the gun in hand, but from what I gathered, the barrel diameter is .625" at the muzzle. I can get a direct thread 1/2"x28 mount for my can. I'm just wondering how you guys would go about this. I can run 1/2"x 28 thread directly into the can, but I've read some folks run a 1/2" to 5/8" adapter then thread suppressor onto the adapter.... Just looking for some options as this is all new to me.

Online fowl smacker

  • Non-Hunting Topics
  • Trade Count: (+3)
  • Sourdough
  • *****
  • Join Date: Oct 2013
  • Posts: 2074
  • Location: Castle Rock
  • Groups: DU, Delta Waterfowl, RMEF, Friends of the Cowlitz
Re: Barrel threading for suppressor question
« Reply #1 on: November 29, 2022, 06:02:00 PM »
I have a Tikka T3 lite in 300wsm that I had threaded and run my Omega 300 directly threaded on it 1/2x28.  No problems.

Offline Sundance

  • Political & Covid-19 Topics
  • Trade Count: (+7)
  • Scout
  • ****
  • Join Date: Jan 2010
  • Posts: 477
Re: Barrel threading for suppressor question
« Reply #2 on: November 29, 2022, 07:02:56 PM »
Rearden Mfg. DPB muzzle break, attach to barrel after threading to 1/2x28, time it up and use rocktite. Get an Atlas adapter or a plan B to put on the can, much easier to thread on/off and then when the can isn’t being used you still have a brake installed.

Offline fly-by

  • Forum Sponsor
  • Trade Count: (+7)
  • Longhunter
  • *****
  • Join Date: Nov 2011
  • Posts: 551
  • Location: Snoqualmie, WA
Re: Barrel threading for suppressor question
« Reply #3 on: November 29, 2022, 07:23:48 PM »
Depending on your use may consider shortening and threading simultaneously.  A 24.3" barrel with a can is pretty unwieldy.  I have a couple of .300 WSMs and a .243 at 21" and think it's a good compromise for supressed use.

Direct thread is noticeably lighter.

Offline JohnVH

  • Non-Hunting Topics
  • Trade Count: (0)
  • Sourdough
  • *****
  • Join Date: Feb 2011
  • Posts: 1964
  • Location: PNW
Re: Barrel threading for suppressor question
« Reply #4 on: November 29, 2022, 07:36:20 PM »
I need to thread my T3 light for a silencer yet, and yes, I've used adapters from 1/2 to 5/8 for silencers. Works fine!

Offline Buckjunkie

  • Political & Covid-19 Topics
  • Trade Count: (+1)
  • Longhunter
  • *****
  • Join Date: Oct 2010
  • Posts: 677
  • Groups: USMC Vet, NRA Life Member, SCI Life Member, WAFNAWS Life Member
Re: Barrel threading for suppressor question
« Reply #5 on: November 29, 2022, 08:08:17 PM »
It depends on barrel diameter. If your barrel is thick enough, you can run 5/8 x 24. If it’s too thin then you are likely to run 1/2 x 28. 

I purchased two Q Trash Panda’s which came with 1/2 x 28 and 5/8 x 24 “cherry Bombs” which are the adaptor between the barrel and suppressor.

Makes it easy, because you can adapt either suppress to whatever threaded end you have.

Offline birdshooter1189

  • Trade Count: (+1)
  • Scout
  • ****
  • Join Date: Nov 2013
  • Posts: 399
  • Location: Port Orchard
Re: Barrel threading for suppressor question
« Reply #6 on: November 29, 2022, 09:05:54 PM »
I threaded my .243 to 1/2x28 because the barrel was too small for 5/8x24. It works fine. I think 1/2x28 would be ok on 7mm also.  I've also used 1/2x28 to 5/8x24 adapters. about $15 on ebay. That works fine too.

Offline jaymark6655

  • Political & Covid-19 Topics
  • Trade Count: (0)
  • Sourdough
  • *****
  • Join Date: Aug 2009
  • Posts: 1879
  • Location: Bedford, IN
Re: Barrel threading for suppressor question
« Reply #7 on: November 30, 2022, 03:54:40 AM »
Seems like most suppressors for this application will be 5/8-24. Major thread diameter will be 0.6167 - 0.6239, so might be possible to do it without using an adapter. Probably better to take an 1/2-inch off barrel and then threading. I hate using adapters, just on more alignment/tolerance issue to worry about. Direct thread always seems to be better than installing over a muzzle device from my experience so far.
"That's the reason we pay $25 for a recoil lug made by a professional instead of one for $0.50 made by Micheal J Fox using a dremel!"

"Women should be treated the same as a French Rifle, dropped at the first sign of trouble."

Offline Bareback

  • Political & Covid-19 Topics
  • Trade Count: (+7)
  • Longhunter
  • *****
  • Join Date: Aug 2020
  • Posts: 503
  • Location: Whidbey Island
Re: Barrel threading for suppressor question
« Reply #8 on: November 30, 2022, 07:28:05 AM »
The largest thread possible. It will be the most rigid and less components to fail, strip, come loose, be out of alignment, warp, bend, affect TIR, etc……

7mm bore is .280. Minor diameter 1/2-28 about .455. The wall thickness after threading approximately .087.
Minor diameter 5/8-24 about .560. Wall thickness after threading approximately .140

The clearance at the end of a thread for run out is the weakest part and that’s the minor diameter of the thread.

Offline Duckslayer89

  • Political & Covid-19 Topics
  • Trade Count: (+2)
  • Frontiersman
  • *****
  • Join Date: Oct 2014
  • Posts: 4081
  • Location: Cut Bank, Montana
Re: Barrel threading for suppressor question
« Reply #9 on: November 30, 2022, 07:36:20 AM »
I have a Bartlein 3 all steel barrel and my smith cut my 26 down to 24 for 5/8-24 threads

Offline fly-by

  • Forum Sponsor
  • Trade Count: (+7)
  • Longhunter
  • *****
  • Join Date: Nov 2011
  • Posts: 551
  • Location: Snoqualmie, WA
Re: Barrel threading for suppressor question
« Reply #10 on: November 30, 2022, 08:52:01 AM »
9/16-24 allows a safe wall thickness and more flexibility in barrel length.  A lot of smiths won't do 1/2-28 on a .308 bore due to wall thickness. 7mm is marginal.  Adapters should be avoided if possible.

Offline raydog

  • Trade Count: (+4)
  • Longhunter
  • *****
  • Join Date: Nov 2012
  • Posts: 782
  • Location: Wetside
  • Groups: RMEF
Re: Barrel threading for suppressor question
« Reply #11 on: November 30, 2022, 10:31:35 AM »
Thanks for the helpful replies hunt wa. I appreciate all the help.


Offline raydog

  • Trade Count: (+4)
  • Longhunter
  • *****
  • Join Date: Nov 2012
  • Posts: 782
  • Location: Wetside
  • Groups: RMEF
Re: Barrel threading for suppressor question
« Reply #12 on: November 30, 2022, 10:33:03 AM »
9/16-24 allows a safe wall thickness and more flexibility in barrel length.  A lot of smiths won't do 1/2-28 on a .308 bore due to wall thickness. 7mm is marginal.  Adapters should be avoided if possible.

Does threading 9/16 allow for a large enough "shoulder" to run the suppressor into? That would be my only concern with that.

Offline b23

  • Non-Hunting Topics
  • Trade Count: (+7)
  • Frontiersman
  • *****
  • Join Date: Jan 2010
  • Posts: 3171
  • Location: Spokane Wa.
Re: Barrel threading for suppressor question
« Reply #13 on: November 30, 2022, 12:08:00 PM »
The Tikka superlite barrels are fairly small at the muzzle.  My 300WSM Tikka SL is right around .618 at the muzzle and .633 one inch from the end of the flutes.  Most direct thread suppressors, except for 223 and rimfire cans, are 5/8x24 and TBAC and others recommend a min. .725 OD at muzzle for 5/8x24, .662 for 9/16x24, and .600 for 1/2x28.  https://thunderbeastarms.com/tech/thread-specifications

If the Tikka superlite barrels weren't fluted you could chop it back a few inches and gain some muzzle diameter.  I've seen some people shorten fluted barrels and I guess it works out ok for them.  I'm probably over cautious so I would never have a fluted barrel shortened back in to the fluted part.


Offline fly-by

  • Forum Sponsor
  • Trade Count: (+7)
  • Longhunter
  • *****
  • Join Date: Nov 2011
  • Posts: 551
  • Location: Snoqualmie, WA
Re: Barrel threading for suppressor question
« Reply #14 on: December 01, 2022, 05:55:40 AM »
9/16-24 allows a safe wall thickness and more flexibility in barrel length.  A lot of smiths won't do 1/2-28 on a .308 bore due to wall thickness. 7mm is marginal.  Adapters should be avoided if possible.

Does threading 9/16 allow for a large enough "shoulder" to run the suppressor into? That would be my only concern with that.
It will require less shortening to create a shoulder than 5/8-24 would, but more than 1/2-28.
https://thunderbeastarms.com/tech/thread-specifications

 


* Advertisement

* Recent Topics

SimplePortal 2.3.7 © 2008-2024, SimplePortal