collapse

Advertisement


Author Topic: DR Brush Mower won't crank  (Read 5906 times)

Offline Rob

  • Non-Hunting Topics
  • Trade Count: (+3)
  • Frontiersman
  • *****
  • Join Date: Apr 2009
  • Posts: 4839
  • Location: Sandpoint ID
DR Brush Mower won't crank
« on: June 09, 2025, 08:05:20 AM »
Equipment info
• DR Power Field and Brush Mower Pro 26 14.5 HP
• Brush Mower Model: AT45026BEN
• Engine Model: 31R6770017G1 (Model 310000 in the manual)

Situation
I have a DR Mower Pro26. It has mostly sat for the last year - inside in the garage. Oil is clean and fresh, Battery was on a trickle charger over the winter and shows charged ~12 volts.

I went to use it a week ago. It cranked fine and started right up. I had it in first gear and mowed about a 20 foot section. I attempted to shift into reverse to back up and the cable used to downshift broke. the engine remained on but I was unable to downshift out of first. I shut down the engine and pushed it back to the garage.

I jerry-rigged a temp fix for the cable while I awaited the replacement cable. I am now able to move thru all the gears.

Problem
Now to Problem. When I turn the key, nothing happens. no buzzing, no attempt to start, nothing.

Troubleshooting so far
1. I went back to the manual and re-read the starting instructions. PTO must be disengaged to start, and the gear must be in neutral. There is also a "plug" for the neutral disengage switch below the handlebars on the lower part of the engine area that appears to be solidly plugged in.
- I verified that all of these seemed fine. When in gear it is very difficult to roll the mower by pushing, and when it is in neutral, it of course rolls well. So I am positive the engine is in neutral when I am trying to start it
2. Verified the battery connections are secure and the battery has at least 12 volts. All check out
3. Verified the PTO was disengaged
4. Verified the switch for the key has all the connections still securely attached.
5. For what it is worth, I tried cranking with and without the "operator present" handle engaged with no effect (even though this is irrelevant to the normal starting procedure).


So... My guess is, that because it was cranking, starting, running fine, and then, after a clean shut down following a shifting problem, it stopped working, my theory is that some kind of safety switch has disabled the ability to crank. Likely either something is telling the machine it is still in gear, or the PTO is on when it is not. I have exhausted the checks I can think of. I will be removing some of the cowlings and such to replace that cable so perhaps something will pop out to me when I do that.

Anyone have this issue before or have ideas to check?
_______________________________________
Sit tall in the saddle, hold you head up high.
Keep your eyes fixed on where the trail meets the sky.
Live like you ain’t afraid to die.
Just sit back and enjoy your ride
  - Chris Ledoux

Offline Woodchuck

  • GO TEAM!!!
  • Global Moderator
  • Trade Count: (+13)
  • Explorer
  • *****
  • Join Date: Mar 2009
  • Posts: 12146
  • Location: Walla Walla
  • HuntWA Woodblock
Re: DR Brush Mower won't crank
« Reply #1 on: June 09, 2025, 08:28:42 AM »
Keep it simple, start with, are you getting proper voltage to the starter? If yes, you need a starter. If not, then start backing up the chain, fuse? Relay?
Antlered rabbit tastes like chicken


Inuendo, wasn't he an Italian proctoligist?

Offline Encore 280

  • Non-Hunting Topics
  • Trade Count: (+11)
  • Sourdough
  • *****
  • Join Date: Oct 2011
  • Posts: 1993
  • Location: Poulsbo
  • Groups: Encore 280
Re: DR Brush Mower won't crank
« Reply #2 on: June 09, 2025, 08:37:39 AM »
Starter solenoid? Any spark between the solenoid posts?

Offline EnglishSetter

  • Trade Count: (+2)
  • Scout
  • ****
  • Join Date: Nov 2024
  • Posts: 267
  • Location: Winlock
  • Groups: NRA
Re: DR Brush Mower won't crank
« Reply #3 on: June 09, 2025, 09:20:23 AM »
I have effectively the same mower.  Same thing happened a few weeks ago sans the shift cable.

I was getting no voltage to the solenoid (and hence none to the starter).  With a jumper battery to the starter and solenoid it cranked fine, but no run.  Checked fuse, looked good.  Removed switch and though i don't have a schematic, the wire colors give a clue and it checked out with ohm meter.  Verified neutral and confirmed with ohm meter. 

So reviewing the 12v path, I suspected the fuse once again.  Removed it, visually good.  Ohm'd it and it failed.  Rummaged around, found a fuse, installed and voila.  I think the first time I've had a glass fuse fail with no witness.

So I'd start with the fuse (and ohm it).  I'd ohm the neutral switch.  I'd test solenoid and starter with jumper battery.  Pretty much that order.  Stop when it cranks/runs.  ;)

Offline Rob

  • Non-Hunting Topics
  • Trade Count: (+3)
  • Frontiersman
  • *****
  • Join Date: Apr 2009
  • Posts: 4839
  • Location: Sandpoint ID
Re: DR Brush Mower won't crank
« Reply #4 on: June 09, 2025, 10:19:24 AM »
I love the idea of checking voltage at the starter.  Will do that

I did visually check the fuse (forgot to mention that).  But I will ohm it as well.  Great thought.

It just seems so weird that it was working, the cable broke, and once I was able to move it into neutral, it no longer cranks.  It was about 3-4 days between the issue and my jerry rigging the cable, but it just sat in the garage between those two events. 

I did pull it about 40 yards to the garage in gear with the power off after it failed.  I can't see how that would have caused any issues other than my back.
_______________________________________
Sit tall in the saddle, hold you head up high.
Keep your eyes fixed on where the trail meets the sky.
Live like you ain’t afraid to die.
Just sit back and enjoy your ride
  - Chris Ledoux

Offline EnglishSetter

  • Trade Count: (+2)
  • Scout
  • ****
  • Join Date: Nov 2024
  • Posts: 267
  • Location: Winlock
  • Groups: NRA
Re: DR Brush Mower won't crank
« Reply #5 on: June 09, 2025, 11:05:03 AM »
The neutral safety switch is just a switch.  In neutral you should have continuity between the 2 pins. Been known to jumper them on a boat trans to get home. 

Not sure how the PTO/electric clutch interrupt works.   Similar I'm sure. 




Offline Rob

  • Non-Hunting Topics
  • Trade Count: (+3)
  • Frontiersman
  • *****
  • Join Date: Apr 2009
  • Posts: 4839
  • Location: Sandpoint ID
Re: DR Brush Mower won't crank
« Reply #6 on: Today at 04:00:06 PM »
Well, I finally had an hour to sit down and troubleshoot the mower.  Very odd (in my opinion)
I replaced the cable that broke - that was easier than I thought.  I verified I could shift through all the gears with it.  Still would not start (not surprised)

Next, I bypassed the neutral safety switch.  Would not crank (remember, it was not even trying to crank, no whirring, no popping, nothing.)

I decided to bypass the battery and jump it off of another battery.  Started right up.

So, it looks like the battery is totally dead.  This is odd to me as it strongly cranked without issue last time that I started it and the shift cable broke - just about a week or so ago.
_______________________________________
Sit tall in the saddle, hold you head up high.
Keep your eyes fixed on where the trail meets the sky.
Live like you ain’t afraid to die.
Just sit back and enjoy your ride
  - Chris Ledoux

Offline Boss .300 winmag

  • FLY NAVAL AVIATION
  • Washington For Wildlife
  • Trade Count: (+22)
  • Explorer
  • ******
  • Join Date: Oct 2010
  • Posts: 18775
  • Location: Skagit Valley
  • How do you measure trying, you do, or you don’t.
Re: DR Brush Mower won't crank
« Reply #7 on: Today at 05:03:05 PM »
Batteries can be that way, one minute good the next not.🤯
"Just because I like granola, and I have stretched my arms around a few trees, doesn't mean I'm a tree hugger!
Hi I'm 8156, our leader is Bearpaw.
YOU CANNOT REASON WITH A TIGER WHEN YOUR HEAD IS IN ITS MOUTH! Winston Churchill

Keep Calm And Duc/Ski Doo On!

 


* Advertisement

* Recent Topics

Drew Cleman Mountain Any Ram! by addicted1
[Today at 10:46:50 PM]


Swakane Ram by Gentrys
[Today at 09:55:58 PM]


After a couple years of poor health,... by Gentrys
[Today at 09:51:47 PM]


September mule deer velvet by jstone
[Today at 08:43:04 PM]


Selkirk bull moose. by trophyhunt
[Today at 07:54:48 PM]


Jim Horn's elk calling, instructional audio CD's. by WapitiTalk1
[Today at 07:40:33 PM]


DR Brush Mower won't crank by Boss .300 winmag
[Today at 05:03:05 PM]


Goose hunting with vice grips by Pegasus
[Today at 04:51:23 PM]


Colockum Archery Bull Tag by geauxtigers
[Today at 04:40:38 PM]


Public Land Sale Senate Budget Reconciliation by GeoSwan
[Today at 04:12:47 PM]


Back up camera by Blacklab
[Today at 11:54:30 AM]


Drew Quality by hunter399
[Today at 11:12:45 AM]


Youth Cow Tag by Sundance
[Today at 10:55:51 AM]


Idaho 2025 Controlled Hunts by huntinluva
[Today at 10:01:53 AM]


Cowiche Quality Buck by buglebuster
[Today at 05:58:49 AM]


People on Cams by hunter399
[Today at 05:56:38 AM]


Norway pass Elk by furbearer365
[Today at 05:46:12 AM]


Norway Pass Bull by High Climber
[Yesterday at 09:23:10 PM]


Greenriver quality Elk permit by IDWAHunt
[Yesterday at 07:54:08 PM]


Steel Targets??? by bowman
[Yesterday at 07:41:07 PM]

SimplePortal 2.3.7 © 2008-2025, SimplePortal