collapse

Advertisement


Author Topic: windage not centered after bore sighting ?  (Read 8732 times)

Offline huntandjeep

  • Trade Count: (+13)
  • Frontiersman
  • *****
  • Join Date: May 2009
  • Posts: 2899
  • Location: West Valley , Yakima
windage not centered after bore sighting ?
« on: April 06, 2014, 01:30:09 PM »
I took the scope off my .17 HMR and replaced it with a Burris Fulfield II I took off another rifle and a new set of rings. The Burris (while on the previous rifle) and previous scope on the .17 were almost in the center of the windage travel after sighting in. Now with the Burris on the .17 I'm almost maxed out to the right in windage before actually sighting it in. What's wrong?
Anyone that thinks a Glock is better than a 1911 paints his toenails.
Yakima Valley Mountaineers

Offline tbotts

  • Past Sponsor
  • Trade Count: (+4)
  • Hunter
  • *****
  • Join Date: Jul 2007
  • Posts: 129
Re: windage not centered after bore sighting ?
« Reply #1 on: April 06, 2014, 01:35:57 PM »
I would try a new set of rings first.  Or just use the rings that were on the .17 with the first scope and use them with the burris.

Offline huntandjeep

  • Trade Count: (+13)
  • Frontiersman
  • *****
  • Join Date: May 2009
  • Posts: 2899
  • Location: West Valley , Yakima
Re: windage not centered after bore sighting ?
« Reply #2 on: April 06, 2014, 01:56:39 PM »
I would try a new set of rings first.  Or just use the rings that were on the .17 with the first scope and use them with the burris.
.  I tried the old rings but they won't allow the objective to clear the barrel with the Burris.
Anyone that thinks a Glock is better than a 1911 paints his toenails.
Yakima Valley Mountaineers

Offline Heredoggydoggy

  • Trade Count: (0)
  • Old Salt
  • ******
  • Join Date: Nov 2010
  • Posts: 5041
  • Location: Wenatchee
  • Team I'M TOO OLD FOR THIS $H!T !
Re: windage not centered after bore sighting ?
« Reply #3 on: April 06, 2014, 02:51:07 PM »
Bore sighting only gets you "on the paper" at 25 yards.  Actual shooting is the best test.  I had to shim the scope I put on my 10-22 build when I ran out of elevation adjustment, and it still shot 18' low at 100 yds.  :dunno:
If it was easy, everybody would be doing it.

When Bernie Madoff did it, it's called a "Ponzi Scheme"
When Government does it, it's called "Social Security"

Offline oddjob

  • Trade Count: (0)
  • Pilgrim
  • *
  • Join Date: Apr 2014
  • Posts: 3
  • Location: puyallup Wa.
Re: windage not centered after bore sighting ?
« Reply #4 on: April 06, 2014, 02:58:39 PM »
   If your 10-22 is shooting 18 feet low at 100yds,you better have a gunsmith do your scope mounting for you! :bash:

Offline huntandjeep

  • Trade Count: (+13)
  • Frontiersman
  • *****
  • Join Date: May 2009
  • Posts: 2899
  • Location: West Valley , Yakima
Re: windage not centered after bore sighting ?
« Reply #5 on: April 06, 2014, 03:15:23 PM »
Bore sighting only gets you "on the paper" at 25 yards.  Actual shooting is the best test.  I had to shim the scope I put on my 10-22 build when I ran out of elevation adjustment, and it still shot 18' low at 100 yds.  :dunno:
.  I realize bore sighting only gets ya on paper. But of all the rifles I've bore sighted they have all been  close to the center of there adjustments not maxed out one way.  I have had to shim a scope once because at 25 yards I was 8" low with no more up adjustment. Found out later that Hammers used the wrong bases and that was the last time somebody else set up my rifles. How would one go about shimming for windage anyways ?
Anyone that thinks a Glock is better than a 1911 paints his toenails.
Yakima Valley Mountaineers

Offline elkaholic123

  • Political & Covid-19 Topics
  • Trade Count: (+10)
  • Sourdough
  • *****
  • Join Date: Jun 2008
  • Posts: 1727
  • Location: Lake Stevens
  • Groups: Montana Dirty Dozen,Life member RMEF,NAHC, WSF
Re: windage not centered after bore sighting ?
« Reply #6 on: April 06, 2014, 04:30:53 PM »
What rings are you using?
elkaholic

Offline FC

  • Trade Count: (0)
  • Frontiersman
  • *****
  • Join Date: May 2010
  • Posts: 3954
  • Location: Wa
Re: windage not centered after bore sighting ?
« Reply #7 on: April 06, 2014, 04:36:52 PM »
I don't think you can shim for windage realistically. I would have a look at your ring/base mounting and make sure nothing is amiss first.
The reason there are so many Ruger upgrades is because they're necessary.

Offline huntandjeep

  • Trade Count: (+13)
  • Frontiersman
  • *****
  • Join Date: May 2009
  • Posts: 2899
  • Location: West Valley , Yakima
Re: windage not centered after bore sighting ?
« Reply #8 on: April 06, 2014, 04:43:54 PM »
What rings are you using?
.  UTG tacticals. Kinda cheapies but they were getting good reviews on Sniperhide so I thought I'd give them a try.   
 I pulled everything apart a little while ago and swapped them end for end ( front to back and back to front) lapped them and still the same thing? I know the picitinny rail on the rifle is good  because with the cheap Weaver picitinney rings that were on it before, after mounting it only took 6-7 clicks to get bore sighted.
Anyone that thinks a Glock is better than a 1911 paints his toenails.
Yakima Valley Mountaineers

Offline Fowlweather25

  • Washington For Wildlife
  • Trade Count: (0)
  • Sourdough
  • *****
  • Join Date: Dec 2011
  • Posts: 1622
  • Location: Rochester, wa
Re: windage not centered after bore sighting ?
« Reply #9 on: April 06, 2014, 05:48:57 PM »
What bore sighter are you using?
What would life be without the thrill of the hunt?

Offline huntandjeep

  • Trade Count: (+13)
  • Frontiersman
  • *****
  • Join Date: May 2009
  • Posts: 2899
  • Location: West Valley , Yakima
Re: windage not centered after bore sighting ?
« Reply #10 on: April 06, 2014, 06:28:31 PM »
What bore sighter are you using?
.   My laser doesn't fit in the barrel of the .17 so I have the gun in my lead sled and am sighting down the barrel and  centering  the neighbors car trailer hub in the barrel. The trailer is 96 yards away. Same way I bore sighted the last scope on this rifle and it worked.
Anyone that thinks a Glock is better than a 1911 paints his toenails.
Yakima Valley Mountaineers

Offline Heredoggydoggy

  • Trade Count: (0)
  • Old Salt
  • ******
  • Join Date: Nov 2010
  • Posts: 5041
  • Location: Wenatchee
  • Team I'M TOO OLD FOR THIS $H!T !
Re: windage not centered after bore sighting ?
« Reply #11 on: April 06, 2014, 06:35:24 PM »
Some Burris rings have inserts you can get to offset a scope.  I used electrical tape to raise the back of my scope enough to get the scope in range.  I think it took a couple of layers of the tape.  It's pretty thin stuff.  you can shim for windage--it doesn't take much.  According to the guy who boresighted it, it was right on.  Actual shooting showed it wasn't.
If it was easy, everybody would be doing it.

When Bernie Madoff did it, it's called a "Ponzi Scheme"
When Government does it, it's called "Social Security"

Offline Bofire

  • Political & Covid-19 Topics
  • Trade Count: (+5)
  • Old Salt
  • ******
  • Join Date: Oct 2007
  • Posts: 5524
  • Location: Yelm
  • Harley YAR YAR YAR!
Re: windage not centered after bore sighting ?
« Reply #12 on: April 06, 2014, 06:39:25 PM »
If you need to you can buy windage adjustable base, Leupold builds some, others do too I bet.
Carl
When the chips are down..... the buffalo is empty!!

I do not shop at Amazon

Offline Heredoggydoggy

  • Trade Count: (0)
  • Old Salt
  • ******
  • Join Date: Nov 2010
  • Posts: 5041
  • Location: Wenatchee
  • Team I'M TOO OLD FOR THIS $H!T !
Re: windage not centered after bore sighting ?
« Reply #13 on: April 06, 2014, 06:55:05 PM »
If you need to you can buy windage adjustable base, Leupold builds some, others do too I bet.
Carl

Warne builds them too, and they are good for rimfires.  had a set on my CZ .204, and it wouldn't hit the same place on the target twice.  Got a set of CZ rings (they are a proprietary mounting system, and the ones Burris made were half the price of the CZ rings, and just as good.) and it solved the problem.
If it was easy, everybody would be doing it.

When Bernie Madoff did it, it's called a "Ponzi Scheme"
When Government does it, it's called "Social Security"

Offline huntandjeep

  • Trade Count: (+13)
  • Frontiersman
  • *****
  • Join Date: May 2009
  • Posts: 2899
  • Location: West Valley , Yakima
Re: windage not centered after bore sighting ?
« Reply #14 on: April 06, 2014, 06:58:50 PM »
If you need to you can buy windage adjustable base, Leupold builds some, others do too I bet.
Carl
.  For a picittiny rail ?
Anyone that thinks a Glock is better than a 1911 paints his toenails.
Yakima Valley Mountaineers

Offline Heredoggydoggy

  • Trade Count: (0)
  • Old Salt
  • ******
  • Join Date: Nov 2010
  • Posts: 5041
  • Location: Wenatchee
  • Team I'M TOO OLD FOR THIS $H!T !
Re: windage not centered after bore sighting ?
« Reply #15 on: April 06, 2014, 07:06:01 PM »
If you need to you can buy windage adjustable base, Leupold builds some, others do too I bet.
Carl
.  For a picittiny rail ?

I like 1-piece scope bases, especially for a picatinny rail.  Never had a problem with those.  Did you check the scope tube for damage from overtightening the rings?  That happens occasionally.  :dunno:
If it was easy, everybody would be doing it.

When Bernie Madoff did it, it's called a "Ponzi Scheme"
When Government does it, it's called "Social Security"

Offline huntandjeep

  • Trade Count: (+13)
  • Frontiersman
  • *****
  • Join Date: May 2009
  • Posts: 2899
  • Location: West Valley , Yakima
Re: windage not centered after bore sighting ?
« Reply #16 on: April 06, 2014, 07:50:23 PM »
If you need to you can buy windage adjustable base, Leupold builds some, others do too I bet.
Carl
.  For a picittiny rail ?

I like 1-piece scope bases, especially for a picatinny rail.  Never had a problem with those.  Did you check the scope tube for damage from overtightening the rings?  That happens occasionally.  :dunno:
.  There's no marks on the scope at all. Going to grab a new set of rings tomorrow and see what happens.
Anyone that thinks a Glock is better than a 1911 paints his toenails.
Yakima Valley Mountaineers

Offline Heredoggydoggy

  • Trade Count: (0)
  • Old Salt
  • ******
  • Join Date: Nov 2010
  • Posts: 5041
  • Location: Wenatchee
  • Team I'M TOO OLD FOR THIS $H!T !
Re: windage not centered after bore sighting ?
« Reply #17 on: April 06, 2014, 08:44:56 PM »
That can be the only problem.  I've used the "sight through the bore and adjust the scope to match" method myself, and it works great!  Make sure you center the windage adjustment on the scope before you mount it, and it shouldn't take much fine tuning to bring it in...  :tup:
If it was easy, everybody would be doing it.

When Bernie Madoff did it, it's called a "Ponzi Scheme"
When Government does it, it's called "Social Security"

Offline BOWHUNTER45

  • Non-Hunting Topics
  • Trade Count: (0)
  • Explorer
  • ******
  • Join Date: Nov 2009
  • Posts: 14731
Re: windage not centered after bore sighting ?
« Reply #18 on: April 06, 2014, 09:19:03 PM »
I have seen a few scopes that are backwards from what they tell you to do ...If you are hitting to the left then try turning it to the right ...it happens ...if someone had the scope before you or someone played with it they could have turned it so many times that you may have to keep turning it until you find the original zero ...usually takes a lot of wasted bullets ...

Offline oddjob

  • Trade Count: (0)
  • Pilgrim
  • *
  • Join Date: Apr 2014
  • Posts: 3
  • Location: puyallup Wa.
Re: windage not centered after bore sighting ?
« Reply #19 on: April 07, 2014, 12:03:17 PM »
   On some scopes you can actually turn adjustments too far and something breaks inside where it won't adjust all the way back.Theres referances to that problem at Pyramid Airguns :yike:

Offline huntandjeep

  • Trade Count: (+13)
  • Frontiersman
  • *****
  • Join Date: May 2009
  • Posts: 2899
  • Location: West Valley , Yakima
Re: windage not centered after bore sighting ?
« Reply #20 on: April 07, 2014, 04:05:27 PM »
Swapped out the rings today and same thing. So going to throw the old scope back on to verify its the Burris.
Anyone that thinks a Glock is better than a 1911 paints his toenails.
Yakima Valley Mountaineers

Offline Heredoggydoggy

  • Trade Count: (0)
  • Old Salt
  • ******
  • Join Date: Nov 2010
  • Posts: 5041
  • Location: Wenatchee
  • Team I'M TOO OLD FOR THIS $H!T !
Re: windage not centered after bore sighting ?
« Reply #21 on: April 07, 2014, 08:09:19 PM »
You probably already know this, but the windage knob doesn't tell you which way the crosshair goes, it dictates which way the point of impact of the bullet goes.  It can be confusing even when you know it!  :tup:
If it was easy, everybody would be doing it.

When Bernie Madoff did it, it's called a "Ponzi Scheme"
When Government does it, it's called "Social Security"

Offline couesbitten

  • Non-Hunting Topics
  • Trade Count: (+2)
  • Sourdough
  • *****
  • Join Date: Nov 2007
  • Posts: 1393
  • Location: East Wenatchee
Re: windage not centered after bore sighting ?
« Reply #22 on: April 08, 2014, 06:50:06 AM »
If I'm taking a scope from one rifle and mounting it on another rifle, I will find "zero" in the scope before mounting and bore sighting by turning the windage and elevation dials to one stop and then counting the number of clicks to the other stop and then putting it half way between the two. This isthe only way I am aware of to get a scope back to a neutral starting point. Don't know if you did this prior to mounting the Burris, but if you didn't, this may be your problem, when you started the process, you were already working with a fraction of your original adjustment range. My  :twocents:
With the catching ends the pleasure of the chase. - Abraham Lincoln

Offline Heredoggydoggy

  • Trade Count: (0)
  • Old Salt
  • ******
  • Join Date: Nov 2010
  • Posts: 5041
  • Location: Wenatchee
  • Team I'M TOO OLD FOR THIS $H!T !
Re: windage not centered after bore sighting ?
« Reply #23 on: April 08, 2014, 07:36:39 AM »
If I'm taking a scope from one rifle and mounting it on another rifle, I will find "zero" in the scope before mounting and bore sighting by turning the windage and elevation dials to one stop and then counting the number of clicks to the other stop and then putting it half way between the two. This isthe only way I am aware of to get a scope back to a neutral starting point. Don't know if you did this prior to mounting the Burris, but if you didn't, this may be your problem, when you started the process, you were already working with a fraction of your original adjustment range. My  :twocents:

 :yeah:  That's what I did with the scope on my 10-22 build.  I got it within 3 inches of zero, then with the elevation range zeroed I was able to fine-tune it from there...  :twocents:
If it was easy, everybody would be doing it.

When Bernie Madoff did it, it's called a "Ponzi Scheme"
When Government does it, it's called "Social Security"

Offline huntandjeep

  • Trade Count: (+13)
  • Frontiersman
  • *****
  • Join Date: May 2009
  • Posts: 2899
  • Location: West Valley , Yakima
Re: windage not centered after bore sighting ?
« Reply #24 on: April 08, 2014, 11:01:48 AM »
If I'm taking a scope from one rifle and mounting it on another rifle, I will find "zero" in the scope before mounting and bore sighting by turning the windage and elevation dials to one stop and then counting the number of clicks to the other stop and then putting it half way between the two. This isthe only way I am aware of to get a scope back to a neutral starting point. Don't know if you did this prior to mounting the Burris, but if you didn't, this may be your problem, when you started the process, you were already working with a fraction of your original adjustment range. My  :twocents:
.    This is exactly how I did it. The Burris has 185 clicks stop to stop, counted back 92 from left stop then mounted scope. After mounted I had to move 75 clicks to the right to get it bore sighted at 96 yards. Going to mount up the old scope tonight and try it , if its good than I guess I'm buying another scope.
Anyone that thinks a Glock is better than a 1911 paints his toenails.
Yakima Valley Mountaineers

Offline huntandjeep

  • Trade Count: (+13)
  • Frontiersman
  • *****
  • Join Date: May 2009
  • Posts: 2899
  • Location: West Valley , Yakima
Re: windage not centered after bore sighting ?
« Reply #25 on: April 08, 2014, 04:20:24 PM »
Looks like the Burris didn't like riding on 2 7mm's. Threw the old Cabelas tactical back on the .17 and after finding the center or the turrets it took 9 clicks to get it bore sighted. Guess I'm buying another Vortex.
Anyone that thinks a Glock is better than a 1911 paints his toenails.
Yakima Valley Mountaineers

Offline Heredoggydoggy

  • Trade Count: (0)
  • Old Salt
  • ******
  • Join Date: Nov 2010
  • Posts: 5041
  • Location: Wenatchee
  • Team I'M TOO OLD FOR THIS $H!T !
Re: windage not centered after bore sighting ?
« Reply #26 on: April 08, 2014, 04:53:43 PM »
Many Burris scopes have a lifetime warranty.  Send it back, and if they repair or replace it, you have a scope to sell if you are still anti-Burris!  :twocents:
If it was easy, everybody would be doing it.

When Bernie Madoff did it, it's called a "Ponzi Scheme"
When Government does it, it's called "Social Security"

Offline huntandjeep

  • Trade Count: (+13)
  • Frontiersman
  • *****
  • Join Date: May 2009
  • Posts: 2899
  • Location: West Valley , Yakima
Re: windage not centered after bore sighting ?
« Reply #27 on: April 08, 2014, 05:51:48 PM »
Many Burris scopes have a lifetime warranty.  Send it back, and if they repair or replace it, you have a scope to sell if you are still anti-Burris!  :twocents:
that was my thought going to get ahold of them in the morning. Its not that I'm anti Burris I still have 4. Just thinking a Vortex cause I have 3 now and really like them and the warranty.
Anyone that thinks a Glock is better than a 1911 paints his toenails.
Yakima Valley Mountaineers

Offline Bmcox86

  • Trade Count: (+3)
  • Sourdough
  • *****
  • Join Date: Apr 2012
  • Posts: 1136
  • Location: Seward, AK
  • One in hand is better than two in the bush
    • Setter Stickers
Re: windage not centered after bore sighting ?
« Reply #28 on: April 08, 2014, 05:59:03 PM »
There's a good deal on a vortex in the classifieds
Semper Paratus

Beretta White Wing 12ga Approx 20k rounds and still going strong!
Tikka t3 light 300wm


http://likeablaze.wordpress.com

 


* Advertisement

* Recent Topics

Idaho General Season Going to Draw for Nonresidents by hunter_sean08
[Today at 02:49:55 PM]


Colorado Results by vandeman17
[Today at 02:29:43 PM]


Resetting dash warning lights by HikerHunter
[Today at 01:49:31 PM]


What's flatbed pickup life like? by Boss .300 winmag
[Today at 01:29:15 PM]


Burrowing Animal by b0bbyg
[Today at 12:43:47 PM]


Cold bore or fouled barrel. by hunter399
[Today at 12:36:22 PM]


Please Report Problems & Bugs Here by HntnFsh
[Today at 09:13:54 AM]


The time clock has started.....and go. by hunter399
[Today at 07:37:38 AM]


DIY Ucluelet trip by CP
[Today at 05:48:15 AM]


Oregon spring bear by time2hunt
[Yesterday at 08:03:28 PM]


Oregon Seed #'s by Doublelunger
[Yesterday at 07:35:15 PM]


WDFW falsely advertising preference points by hunter399
[Yesterday at 04:38:43 PM]


Black Eagle arrows deals by kodiak06
[Yesterday at 02:02:59 PM]


2025 Multiseason Deer General? by Goshawk
[Yesterday at 12:23:10 PM]


Last year putting in… by Dirtnap
[Yesterday at 11:48:14 AM]

SimplePortal 2.3.7 © 2008-2025, SimplePortal