collapse

Advertisement


Author Topic: Thread locker removal?  (Read 3020 times)

Offline Blacktail Sniper

  • Trade Count: (+6)
  • Old Salt
  • ******
  • Join Date: Oct 2009
  • Posts: 5912
  • Location: Rochester, Washington
  • Kill'em all...let the gravy sort'em out!!!
  • Groups: blacktail sniper
Thread locker removal?
« on: September 30, 2014, 03:17:08 PM »
Here is one I am struggling with.  I have a rifle with rings & bases that I want to swap out. The rub is, it appears the base screws were attached with a thread locker of some type or possibly even some type adhesive.

I tried removing them, but there was just no give after what I felt should have been an adequate amout of force to break the screws free.  My concern at this point is to not break one or more off in the receiver. 

Was thinking rest the rifle upside down and drop some sort of agent into the bottom of the thread holes and hoping it will wick up and lossen whatever is holding the screws?

Any suguestions as to what I should try and use?

On the upside, if I can't get them free, I know the bases are solid....
It is better to be consistently incorrect than inconsistently correct...

Sarcasm: The ability to insult stupid people without them realizing it. 

My level of sarcasm depends on your level of stupidity...

Sarcasm makes smart people laugh and stupid people mad.

Offline huntandjeep

  • Trade Count: (+13)
  • Frontiersman
  • *****
  • Join Date: May 2009
  • Posts: 2901
  • Location: West Valley , Yakima
Re: Thread locker removal?
« Reply #1 on: September 30, 2014, 03:23:44 PM »
Try a little heat  :tup:
Anyone that thinks a Glock is better than a 1911 paints his toenails.
Yakima Valley Mountaineers

Offline Blacktail Sniper

  • Trade Count: (+6)
  • Old Salt
  • ******
  • Join Date: Oct 2009
  • Posts: 5912
  • Location: Rochester, Washington
  • Kill'em all...let the gravy sort'em out!!!
  • Groups: blacktail sniper
Re: Thread locker removal?
« Reply #2 on: September 30, 2014, 03:28:46 PM »
I actually thought about that, but of all the things taken when my place was burglarized was a little pin-point sized butane torch.

   :bash:

I don't have a heat gun and am afraid that my full size propane torch would be too much and damage the bluing.
It is better to be consistently incorrect than inconsistently correct...

Sarcasm: The ability to insult stupid people without them realizing it. 

My level of sarcasm depends on your level of stupidity...

Sarcasm makes smart people laugh and stupid people mad.

Offline Rick

  • Non-Hunting Topics
  • Trade Count: (0)
  • Sourdough
  • *****
  • Join Date: Dec 2007
  • Posts: 1858
  • Location: Everett
Re: Thread locker removal?
« Reply #3 on: September 30, 2014, 04:05:43 PM »
Got a soldering gun? Heat the screwhead that way.

I use blue Locktite all the time. Never had an issue breaking them free. Hopefully red wasn't used.

Online mountainman

  • Political & Covid-19 Topics
  • Trade Count: (0)
  • Old Salt
  • ******
  • Join Date: Mar 2007
  • Posts: 5955
  • Location: Wenatchee, Wa
Re: Thread locker removal?
« Reply #4 on: September 30, 2014, 09:51:29 PM »
With a very tight screw driver, give a few sharp raps to the end of drive to try and spread the threads of the screws and break the bond.
That Sword is more important than the Shield!

Offline Hawgdawg

  • Trade Count: (0)
  • Longhunter
  • *****
  • Join Date: Dec 2011
  • Posts: 951
  • Location: Enumscatch
Re: Thread locker removal?
« Reply #5 on: September 30, 2014, 10:03:42 PM »
Be nice to the moderator's and don't break any rules. If the smoke clears they might open the thread up again, as long as everyone plays nice with each other. :bash:

Offline wildweeds

  • Non-Hunting Topics
  • Trade Count: (+1)
  • Sourdough
  • *****
  • Join Date: Oct 2010
  • Posts: 1701
Re: Thread locker removal?
« Reply #6 on: September 30, 2014, 10:11:52 PM »
Locktite is more of a "Feel good" than anything else, properly torqued fine threaded machine screws need nothing more than a drop of oil to lubricate the threads to achieve an accurate torque with less friction drag.Sounds like somebody got all Rambo and went with Red.I'd suggest that your on the right track with trying to melt the offending agent out with a solvent.Do a search for "Ed's Red bore cleaner" mix some up and apply a drop to the underside of each screw, the acetone component may very well eat it up. I use ed's red on everything,it's cheap and quite frankly  to me it performs better than purchased bore cleaning solvents.Mountainmans advice will work,but to my way of thinking when it's all said and done the splayed threads will definately require a thread locker,as the hammering will loosen the fit of the threads.

Offline Seahawk12

  • Trade Count: (+8)
  • Frontiersman
  • *****
  • Join Date: Sep 2014
  • Posts: 3046
  • Location: Kenmore
Re: Thread locker removal?
« Reply #7 on: September 30, 2014, 10:48:12 PM »
Just curious, Have you tried anything like wd40 and Tapping the screw driver?
If the heat and/or wd40 don't work then solvents might work.
LocTite is an acrylic-base adhesive so acetone should work. Though it will be hard to get the stuff to soak down before it evaporates. There is acetone in nail polish remover that is not as concentrated as using the stuff straight up I've also read that a product called Dry Ice will dissolve lock tite but have never tried it.
You may also try a hardware store for super glue solvent, but that's really just acetone, too.
"I make up my opinions from facts and reasoning, and not to suit any body but myself. If people don't like my opinions, it makes little difference as I don't solicit their opinions or votes."
William Tecumseh Sherman

Offline high country

  • Trade Count: (0)
  • Old Salt
  • ******
  • Join Date: May 2007
  • Posts: 5133
Re: Thread locker removal?
« Reply #8 on: October 16, 2014, 09:48:30 PM »
if you suspect locktite.....HEAT IT. Bring it up to 400 degrees and it will release. locktite is used in several oil submerged applications. use a screw driver over the stove, soldering iron, torch......but get some heat on it.

Offline jay.sharkbait

  • Political & Covid-19 Topics
  • Trade Count: (+2)
  • Old Salt
  • ******
  • Join Date: Jun 2013
  • Posts: 6507
Re: Thread locker removal?
« Reply #9 on: October 18, 2014, 05:44:33 PM »
Heat

Soldering iron works great.

You can try tapping a high quality screwdriver as well.

Good luck


Offline wadu1

  • Grumpy
  • Global Moderator
  • Trade Count: (+30)
  • Old Salt
  • *****
  • Join Date: Sep 2008
  • Posts: 7247
  • Location: Tacoma
  • RMEF, DU, NRA, PFE, NWTF
Re: Thread locker removal?
« Reply #10 on: October 18, 2014, 06:46:03 PM »
Heat

Soldering iron works great.

You can try tapping a high quality screwdriver as well.

Good luck
I agree with sharkbait- heat - and a screwdriver that fits the screw tightly. I use a good quality gun-smithing set like B-Square etc. just not Kobalt/Craftsman or Harbor Freight. 
"a fronte praecipitium a tergo lupi"

 


* Advertisement

* Recent Topics

Bow mount trolling motors by Happy Gilmore
[Today at 07:58:22 AM]


2025 OILS! by Ridgerunner
[Today at 07:40:49 AM]


best draw for moose unit wise by Ridgerunner
[Today at 07:40:00 AM]


FFL preferences or warnings in Olympia or south Sound area? by lhrbull
[Today at 06:59:24 AM]


Nooksack Archery Tag by LongBomb
[Today at 06:29:37 AM]


I’m on a blacktail mission by Turner89
[Yesterday at 11:33:35 PM]


Idaho 2025 Controlled Hunts by TeacherMan
[Yesterday at 10:43:16 PM]


AKC lab puppies! Born 06/10/2025 follow as they grow!!! by scottfrick
[Yesterday at 09:54:06 PM]


Basin elk by hughjorgan
[Yesterday at 09:50:49 PM]


Getting back into dogs by bearpaw
[Yesterday at 09:06:14 PM]


Cowiche Quality Buck by Nwgunner
[Yesterday at 08:55:00 PM]


MA-10 Coho by WAcoueshunter
[Yesterday at 08:50:46 PM]


Is FS70 open? by CarbonHunter
[Yesterday at 08:09:04 PM]


Muzzy Mission Quality!!! by NOCK NOCK
[Yesterday at 07:49:11 PM]


Colockum Archery Bull Tag by Smittyk44
[Yesterday at 04:23:53 PM]


49 degrees north late Moose tag by Buzzsaw461
[Yesterday at 04:11:52 PM]


I'm Going To Need Karl To Come up With That 290 Muley Sunscreen Bug Spray Combo by BULLBLASTER
[Yesterday at 03:53:35 PM]


Mature bulls during late season? by Pete112288
[Yesterday at 03:51:08 PM]


Stillaguamish 448 QD rifle tag by Hi-Liter
[Yesterday at 03:23:47 PM]


Vashon Island deer tag by bowhunter_1
[Yesterday at 02:59:43 PM]

SimplePortal 2.3.7 © 2008-2025, SimplePortal