collapse

Advertisement


Author Topic: Reloading--Manual vs Convention (copper bullets)  (Read 1146 times)

Offline JimmyHoffa

  • Non-Hunting Topics
  • Trade Count: (+2)
  • Explorer
  • ******
  • Join Date: Sep 2010
  • Posts: 14547
  • Location: 150 Years Too Late
Reloading--Manual vs Convention (copper bullets)
« on: September 22, 2020, 07:54:45 PM »
When reloading copper bullets in the past, when there wasn't any load data available I would use a little thumb rule.  That was to take the bullet weight and add 15%, then use the closest lead bullet that did have that powder.  So for a 150 gr copper, would look for a 170-ish grain lead which usually ended up being the 165-168 grains.  This was to account for the extra volume of copper (compressed load).  Anyone ever hear of this?
So I got a new manual because I couldn't find anything with a new powder to try (IMR 4451 Enduron).  I noticed the manual doesn't make any mention of differences for the length of the bullets.  It has all the bullets grouped by weight:  A 150 gr GMX (copper) is listed with say a 150 gr interlock SP (copper jacketed lead core).  Even listed as having the same COL, even though side by side the GMX is longer.  The maximum charge listed would be the same, yet the copper sits further into the case.  Just kind of made me wonder.  Is the former advice for using data for the 15% heavier lead bullets just not needed (never was)?  Just burned up more powder during load development by starting even lower than what is now a 'starting point'?

Offline Platensek-po

  • Political & Covid-19 Topics
  • Trade Count: (+5)
  • Sourdough
  • *****
  • Join Date: Oct 2018
  • Posts: 1511
  • Location: Shelton, wa
Re: Reloading--Manual vs Convention (copper bullets)
« Reply #1 on: September 22, 2020, 07:57:43 PM »
Interesting. Would like to hear about this and bump this up
“Under no pretext should arms and ammunition be surrendered; any attempt to disarm the workers must be frustrated, by force if necessary.”

If you are not willing to die for freedom then take the word out of your vocabulary.

Offline Jolten

  • Political & Covid-19 Topics
  • Trade Count: (+7)
  • Longhunter
  • *****
  • Join Date: Jan 2013
  • Posts: 843
  • Location: Yakima, WA
Re: Reloading--Manual vs Convention (copper bullets)
« Reply #2 on: September 22, 2020, 08:11:01 PM »
I believe the COAL is max Sammi spec always. And the powder being the same due to needing just as much force to move an equal amount of weight down the barrel?
The best equipment in the world is useless to the idiot who doesn't understand it.

Offline JimmyHoffa

  • Non-Hunting Topics
  • Trade Count: (+2)
  • Explorer
  • ******
  • Join Date: Sep 2010
  • Posts: 14547
  • Location: 150 Years Too Late
Re: Reloading--Manual vs Convention (copper bullets)
« Reply #3 on: September 22, 2020, 08:24:29 PM »
If I look at the exact same bullet (ex the 180 gr interlock SP) and the same powder RL-17, both listed to be loaded to the cannelure--same depth/same weight bullet, but one goes in the .30-06 and the other goes into a .308, the 06 starts at 47.0 grs and the .308 is at 47.1 grs before the highlighted dangerous territory load is (max recommended).  Then the consideration is from case capacity/pressure.  But the manual says you can load a copper max load the same charge as a lead core for the given weight/powder, but you have a different case capacity.

The manual I'm looking at is the Hornady 10th edition.

Offline yorketransport

  • Political & Covid-19 Topics
  • Trade Count: (+12)
  • Frontiersman
  • *****
  • Join Date: Apr 2009
  • Posts: 3310
  • Location: Yelm
  • Preferred pronouns: were/was
Re: Reloading--Manual vs Convention (copper bullets)
« Reply #4 on: September 22, 2020, 08:44:38 PM »
It has just as much to do with bearing surface as it does bullet make up and weight. Newer monometal bullets have a much shorter bearing surface than the older designs (like the original Barnes bullet), so sometimes the same data can be used for the same weights in lead core and solid copper. When you get into the copper bullets with very short bearing surfaces like the Cutting Edge, Flatline, Badlands, and Hamemers, you'll actually get to a point where your charge weights will be higher with the monometals than they are with a similar weight lead core bullet. A lot of the solid coppers are using different alloys than they used to, so that changes things as well.

Offline hogslayer

  • Trade Count: (+7)
  • Longhunter
  • *****
  • Join Date: Dec 2012
  • Posts: 818
  • Location: Snoqualmie-Belfair
  • Groups: Bloody decks
Re: Reloading--Manual vs Convention (copper bullets)
« Reply #5 on: September 22, 2020, 08:57:29 PM »
I have been playing with Hammer Hunter bullets in 338 NMI.  I am becoming a fan. This was my three shot zero for hunting today. 24” barrel H1000 2980 FPS.   Copper doesn’t swell like lead does.  Same charge for 250 Berger (shortest bearing surface of all time) was 3050.

Offline JimmyHoffa

  • Non-Hunting Topics
  • Trade Count: (+2)
  • Explorer
  • ******
  • Join Date: Sep 2010
  • Posts: 14547
  • Location: 150 Years Too Late
Re: Reloading--Manual vs Convention (copper bullets)
« Reply #6 on: September 22, 2020, 09:04:57 PM »
Okay, that sounds like a good explanation.  The bullet description does say that the new gilding for the metal is friction reduction as well as mentions bearing surface changes.  The old monos that I am used to are Barnes TSX and TTSX, where I used to do the quick volume compensation.  My assumption was based off initial pressure.

 


* Advertisement

* Recent Topics

Looking for Solid 22 LR input by Rat44
[Today at 12:26:36 AM]


Lynx kittens confirmed in the Kettle Range by dwils233
[Today at 12:04:14 AM]


Archery elk gear, 2025. by spin05
[Today at 12:03:42 AM]


How To Get Your $0.00 Tax Stamp - Black Hammer Arms by dreadi
[Yesterday at 11:33:25 PM]


AUCTION: SE Idaho DIY Deer or Deer/Elk Hunt by Rainier10
[Yesterday at 10:19:01 PM]


Seeking recommendations on a new scope by Klickitatsteelie
[Yesterday at 09:23:56 PM]


2025 Canning by Twispriver
[Yesterday at 09:15:12 PM]


2025 Montana alternate list by Edminsterquality
[Yesterday at 08:47:06 PM]


WSTA 2025 Summer Rendezvous Agenda by Trapper John
[Yesterday at 08:00:27 PM]


First attempt at polish sausages by Stein
[Yesterday at 07:58:22 PM]


Fullsized Truck Opinion: HiMiNew vs LoMiOlder by MADMAX
[Yesterday at 07:57:22 PM]


Sockeye Numbers by Southpole
[Yesterday at 07:44:30 PM]


Best all around muzzy (updated) by jjhunter
[Yesterday at 07:44:26 PM]


38% increase in fishing and hunting licenses by Sitka_Blacktail
[Yesterday at 07:02:41 PM]


50 inch SXS and Tracks? by 92xj
[Yesterday at 05:34:03 PM]


3 days for Kings by MADMAX
[Yesterday at 05:06:49 PM]


Full moon and last week of September by pd
[Yesterday at 04:51:23 PM]


Hunting bears in the thick stuff by ghosthunter
[Yesterday at 04:33:46 PM]


GMU 247 Entiat bear hunting by Ridgerunner
[Yesterday at 11:56:01 AM]

SimplePortal 2.3.7 © 2008-2025, SimplePortal