collapse

Advertisement


Author Topic: Made a new trap  (Read 3212 times)

Offline Wolfdog91

  • Trade Count: (0)
  • Tracker
  • **
  • Join Date: Oct 2020
  • Posts: 41
  • Location: South Mississippi
  • Groups: Trapperman.com mississippi trappers assocation
Made a new trap
« on: May 13, 2021, 11:08:35 AM »
Hay wanted to see if I can get a lil critique from y'all cage trappers on this trap I put together. Built it out if scrap panel so it's a little mismatched but seems to work just fine. It's double doored goullitine gates, each has a independent lock and it's runs off of a wire trigger. Trap is made out of 10ga ( I think) horse panel, trigger components are 1/4" cold roll ( as far as the trigger mech arms and trow bars / tabs). Doors are framed with 1/2" cold roll. Slides gate channels are 1x1x1/8" angle. Made it for trail set more than anything. Still need to add the staking rigs to the out side and tweak another thing or two though
So what do y'all think ?

Offline Cougartail

  • Political & Covid-19 Topics
  • Trade Count: (+1)
  • Frontiersman
  • *****
  • Join Date: Oct 2012
  • Posts: 3518
  • Location: Eastern Washington
Re: Made a new trap
« Reply #1 on: May 13, 2021, 11:18:28 AM »
How long is it?
If I need a permit and education to buy a firearm than women should need a permit and education  before getting an abortion.

Voting for Democrats is prima facie evidence you are a skirt wearing, low T, beta male. Do better.

Offline Wolfdog91

  • Trade Count: (0)
  • Tracker
  • **
  • Join Date: Oct 2020
  • Posts: 41
  • Location: South Mississippi
  • Groups: Trapperman.com mississippi trappers assocation
Re: Made a new trap
« Reply #2 on: May 13, 2021, 03:12:05 PM »


Offline Wolfdog91

  • Trade Count: (0)
  • Tracker
  • **
  • Join Date: Oct 2020
  • Posts: 41
  • Location: South Mississippi
  • Groups: Trapperman.com mississippi trappers assocation
Re: Made a new trap
« Reply #3 on: May 13, 2021, 03:12:40 PM »

Offline Humptulips

  • Global Moderator
  • Trade Count: (+2)
  • Old Salt
  • *****
  • Join Date: May 2010
  • Posts: 9108
  • Location: Humptulips
    • Washington State Trappers Association
  • Groups: WSTA, NTA, FTA, OTA, WWC, WFW, NRA
Re: Made a new trap
« Reply #4 on: May 13, 2021, 04:11:44 PM »
Assuming it is made for cat, coyote, beaver, otter I think it is too short, 17 inches into the trap when they trigger it with a guillotine door I think they are likely to hold the door open with their back and back out.
I know a theory has it that if an animal gets hit on the butt they will jump forward. Could be but  17 inches  I think it will drop on the middle of their back. They need to be in a little further IMO.
Could work if there is a lot of play in the trigger and they get past halfway before it springs. :dunno:
Bruce Vandervort

Offline Wolfdog91

  • Trade Count: (0)
  • Tracker
  • **
  • Join Date: Oct 2020
  • Posts: 41
  • Location: South Mississippi
  • Groups: Trapperman.com mississippi trappers assocation
Re: Made a new trap
« Reply #5 on: May 13, 2021, 05:05:50 PM »
Assuming it is made for cat, coyote, beaver, otter I think it is too short, 17 inches into the trap when they trigger it with a guillotine door I think they are likely to hold the door open with their back and back out.
I know a theory has it that if an animal gets hit on the butt they will jump forward. Could be but  17 inches  I think it will drop on the middle of their back. They need to be in a little further IMO.
Could work if there is a lot of play in the trigger and they get past halfway before it springs. :dunno:
just coon, possum and grey fox really. Reason I made it so shot was because it was made of scraps. Didn't really have enought to make a full size trap

Offline Cougartail

  • Political & Covid-19 Topics
  • Trade Count: (+1)
  • Frontiersman
  • *****
  • Join Date: Oct 2012
  • Posts: 3518
  • Location: Eastern Washington
Re: Made a new trap
« Reply #6 on: May 13, 2021, 05:13:56 PM »
42 inches for bobcat traps with double doors?
If I need a permit and education to buy a firearm than women should need a permit and education  before getting an abortion.

Voting for Democrats is prima facie evidence you are a skirt wearing, low T, beta male. Do better.

Offline JakeLand

  • WA State Trappers Association
  • Trade Count: (+35)
  • Frontiersman
  • *****
  • Join Date: Oct 2011
  • Posts: 4512
  • Location: Wet side
Re: Made a new trap
« Reply #7 on: May 13, 2021, 06:17:08 PM »
I have one with spring loaded doors and a coin trigger that’s 48” long ,you set both doors or singular and I’ve had succes where otters have gone into crawl spaces so it’s basically like a comstock but bigger and I can use it on bobcats with just a single door

Offline Humptulips

  • Global Moderator
  • Trade Count: (+2)
  • Old Salt
  • *****
  • Join Date: May 2010
  • Posts: 9108
  • Location: Humptulips
    • Washington State Trappers Association
  • Groups: WSTA, NTA, FTA, OTA, WWC, WFW, NRA
Re: Made a new trap
« Reply #8 on: May 14, 2021, 09:55:37 PM »
My double door beaver, otter, cat traps are 40" long, never a problem. I make the shorties for beaver and otter at 32" ling. All those have the inward opening doors. Guillotine doors are a different matter though. I believe the trap would have to be longer with guillotine doors.

I'm not sure what size your possum are but I would think most would slip out of 4x4 mesh. Maybe that is a good thing> :chuckle:
Bruce Vandervort

Offline Wolfdog91

  • Trade Count: (0)
  • Tracker
  • **
  • Join Date: Oct 2020
  • Posts: 41
  • Location: South Mississippi
  • Groups: Trapperman.com mississippi trappers assocation
Re: Made a new trap
« Reply #9 on: May 15, 2021, 06:56:56 PM »
My double door beaver, otter, cat traps are 40" long, never a problem. I make the shorties for beaver and otter at 32" ling. All those have the inward opening doors. Guillotine doors are a different matter though. I believe the trap would have to be longer with guillotine doors.

2x4" actually, never had much of a problem holding smaller critters with it in other traps  :)

I'm not sure what size your possum are but I would think most would slip out of 4x4 mesh. Maybe that is a good thing> :chuckle:

 


* Advertisement

* Recent Topics

AKC lab puppies! Born 06/10/2025 follow as they grow!!! by scottfrick
[Today at 12:50:25 PM]


Brittany spaniel puppy by high_hunter
[Today at 12:24:39 PM]


Best all around muzzy (updated) by trophyhunt
[Today at 12:09:26 PM]


Westside muzzy bull by trophyhunt
[Today at 12:07:55 PM]


Leupold Display fade by royalbull
[Today at 12:06:30 PM]


I'm Going To Need Karl To Come up With That 290 Muley Sunscreen Bug Spray Combo by highside74
[Today at 11:41:09 AM]


Wa, Or & NW Regional Sanctioned Duck Calling Contest by Brute
[Today at 11:28:33 AM]


2025 Montana alternate list by tdot24
[Today at 08:24:52 AM]


10 years ago- Now by kball4
[Today at 07:33:37 AM]


Should I come back or find someplace else? by addicted1
[Yesterday at 11:24:45 PM]


Up DATE!1993 Merc issues getting up on plane by EnglishSetter
[Yesterday at 06:57:24 PM]


2025 NWTF Jakes Day by wadu1
[Yesterday at 06:51:15 PM]


49 Degrees North Early Bull Moose by NOCK NOCK
[Yesterday at 05:28:30 PM]


Also looking for help deciding on a scope by dreadi
[Yesterday at 04:58:22 PM]


Need information on having a gunsmith thread a barrel for thin walled chokes. by Badhabit
[Yesterday at 02:37:23 PM]


How To Get Your $0.00 Tax Stamp - Black Hammer Arms by dreadi
[Yesterday at 02:34:04 PM]


Teanaway bull elk by Ridgerunner
[Yesterday at 01:55:35 PM]


Quinault Bear guide/help by blackdog
[Yesterday at 01:14:17 PM]


HUNTNNW 2025 trail cam thread and photos by Crunchy
[Yesterday at 11:20:34 AM]


Gots me a new/old rockchuck rifle coming by JDHasty
[July 12, 2025, 10:41:07 PM]

SimplePortal 2.3.7 © 2008-2025, SimplePortal