Reloading Bench

[timberghost72]

So I just recieved my reloading kit (Lee Challenger Kit) and am wondering of those of you who reload, are you set up in the house or in the garage/shop?  Also if ya got any pics to post so I could get ideas on how to set up my bench that would be cool.  I can't wait to learn this.

[Ray]

I used a 3/4 inch piece of plywood. I cut that to suit an area in my small storage room. Then I found some 4x4s and used those for legs. I stabilized the legs by attaching the leftover plywood down low on the legs. It sits on top of carpet and works well.  Then I drilled the holes for the bolts which attach on for the press.

[WDFW-SUX]

I'll take some pics of mine and post tomorrow.

[littlebuf]

my reloading bench is 10 feet long with a full set of kitchen cabinet uppers above it and its still to small. take that for what its worth. oh ya welcome to the sickness you can forget about saving money that's just a myth

[road.kill]

reloading benches can clutter up fast, i know this from first hand experience and that was just from loading shotshells

[jeepasaurusrex]

Be careful using carpet in a reloading room. An old friend of ours who used to run the Kenmore Gun range many years ago, also taught my Dad how to reload. He said to never use carpet in the reloading room due to the chance of static discharge creating an explosion.

When I was in the Army, I worked on electronics. We had to wear static discharge bands around our wrist that were hooked to the bench, and a ground. 

[Gobble Gobble]

My wife taught me how to reload   I'm such a lucky man  

We used to use a 5 foot wooden folding table that we just drilled holes into for the press bolts. One of the greatest things I use for storage is the nut & bolt organizers everyone has on the garage workbench, great for keeping all the differant caliber dies and press components separate.

Sad to say we are in an apartment at this time so no reloading but I do have blue prints for a new bench when we have the room again.

[Huntbear]

My bench is 4x4 square.  It is made from 1 1/2 in. angle iron welded together.  I then decked it with 2x10s bolted down to the angle.  I have a full size shelf under it that holds all kind of rubbermaid bins for all the accessory stuff you need.  I want a cabinet on the wall over it, for powder storage, but for now, I use a water proof ammo box.  I have had 2 presses set up on this bench and you can work side by side, with room to spare.  However, I never have anything out that I do not need at the moment, and everything has its place.  Organization is the key to any reloading bench.

That said, if I was to do it over again, it would be 8 or 10 foot long, just because I like room to work.

[Ghost1941]

I'll take pictures of mine tomorrow and send them along.

[MerriamMan]

Yeah, That would be great ghost, I wish everyone that could, would post a picture of their bench so us green re loaders could get some ideas. Rut16 and I are just about to start building one for ourselves. Thanks

[Ghost1941]

Mine cost a grand total of 30 dollars and we stood 5 joe's on it.  So I'll set ya up with some pictures

[WDFW-SUX]

Here is mine

[Ghost1941]

As requested:

[Ray]

Here's my bench. With the lighter in the middle and sitting on some carpet. 

Oh yes and I believe that scale is from the 1950s or 1960s with the original Lee box. Still kickin after all these years.

[Crisptrigr]

If you live on the westside (wetside) you may want to consider doing your reloading indoors where it is warm and dry. Primers will absorb moisture and become unreliable, you won't know until it's too late. Your dies and press will rust and powder is harder to measure properly when you're shivering.

I understand the temptation of "disappearing" in the garage for us guys especially when you want to focus on a task and enjoy your craft. However, reloading comes with inherent risks and boundaries, "keeping your powder dry" isn't just for front stuffers.

Good luck and have fun in your new endeavor!