collapse

Advertisement


Author Topic: bullet seating depth?  (Read 1909 times)

Offline logan

  • Trade Count: (0)
  • Tracker
  • **
  • Join Date: Mar 2009
  • Posts: 45
  • Location: buckley,wa
bullet seating depth?
« on: June 07, 2012, 06:18:21 PM »
I'm reloading a 300 win mag with barns 168 tsx btls. I'm using a hornady press and die. and my overall length is 2.920. to finish what i started i had to buy a new box of bullets. when i reloaded those i was getting 2.922-2.925. so i check every thing i could think of does anybody have any suggestions.

Offline wsmnut

  • Trade Count: (0)
  • Scout
  • ****
  • Join Date: Dec 2008
  • Posts: 449
  • Location: Twisp, WA
Re: bullet seating depth?
« Reply #1 on: June 07, 2012, 06:32:55 PM »
Are you using a bullet comparator for measuring?  Or are you
measuring the over all length?  I am going to guess you are using COL.
Bullet lengths vary, and since the tip doesn't engage the rifling, it's not
important unless your cartridge won't fit in the magazine.
     Find a comparator for .30 caliber and you'll be a lot more precise.

Good Luck

wsmnut
Wsmnut


Belief is so often the death of reason.
Moron Lube

Offline Biggerhammer

  • Political & Covid-19 Topics
  • Trade Count: (0)
  • Old Salt
  • ******
  • Join Date: Jun 2011
  • Posts: 5142
  • Location: Central Washington
  • Powder, primer, bullet JUNKIE.
Re: bullet seating depth?
« Reply #2 on: June 07, 2012, 06:57:37 PM »
Is your die set up to seat off the tip or the ogive? You will always have that problem if your seating off the tip and measuring overall length. Get a comparator, measure off the ogive. Set it and forget it.

Offline JackOfAllTrades

  • Rasbo said I Ain't Right.
  • Trade Count: (0)
  • Old Salt
  • ******
  • Join Date: Feb 2009
  • Posts: 6509
  • Location: Lynden, WA.
  • Μολὼν λαβέ
Re: bullet seating depth?
« Reply #3 on: June 07, 2012, 07:07:04 PM »
Agree'd..

Make the loaded cartridge fit in the magazine and move freely so it cycles through the action to chamber.

For the beginning reloader, I suggest that the OAL, is really a measurement from the case base to the ogive where it would contact the lands of the bore. Learn how to do this.  (Bullet comparator)   Backing off .005-.009" from the lands is a good place to start and will likely be quite close to the OAL (sammi) spec in the book.

That said, the barns 168 tsx is not a lead exposed bullet so measured bullet length should be quite consistent. (measure a bunch of the bullets and come up with an average length out of one lot/box.)

Your loaded cartridges should not vary more than +-.003".  If you're loading for hunting purposes and not long range sniping, then you'll never notice +-.005" difference having an effect on accuracy.

-Steve
The NRA says I'm a Master!
Colt's, Ruger's, Dan Wesson, & Kimber are my friends!
Proud to be a U.S. Navy Veteran.

If you never follow your dreams, you'll never go anywhere.

Critical thinking keeps people from freaking the hell out every time some half baked blogger forgets his meds. Unlike some of you, I do not have TawkethOutOfAnus© syndrome.

Offline JackOfAllTrades

  • Rasbo said I Ain't Right.
  • Trade Count: (0)
  • Old Salt
  • ******
  • Join Date: Feb 2009
  • Posts: 6509
  • Location: Lynden, WA.
  • Μολὼν λαβέ
Re: bullet seating depth?
« Reply #4 on: June 07, 2012, 07:16:07 PM »
Why is it that new reloaders must spend hard earned cash on premium bullets?  To the rest of the readers, ... Remington Power Points bulk packed at Cabelas are less than half the price to practice/learn with.

-Steve
The NRA says I'm a Master!
Colt's, Ruger's, Dan Wesson, & Kimber are my friends!
Proud to be a U.S. Navy Veteran.

If you never follow your dreams, you'll never go anywhere.

Critical thinking keeps people from freaking the hell out every time some half baked blogger forgets his meds. Unlike some of you, I do not have TawkethOutOfAnus© syndrome.

Offline Biggerhammer

  • Political & Covid-19 Topics
  • Trade Count: (0)
  • Old Salt
  • ******
  • Join Date: Jun 2011
  • Posts: 5142
  • Location: Central Washington
  • Powder, primer, bullet JUNKIE.
Re: bullet seating depth?
« Reply #5 on: June 07, 2012, 07:37:11 PM »
Why is it that new reloaders must spend hard earned cash on premium bullets?  To the rest of the readers, ... Remington Power Points bulk packed at Cabelas are less than half the price to practice/learn with.

-Steve

What?? I'm supposed to be shooting something other than Barnes???   :chuckle: :chuckle: :chuckle: :chuckle:

Offline JackOfAllTrades

  • Rasbo said I Ain't Right.
  • Trade Count: (0)
  • Old Salt
  • ******
  • Join Date: Feb 2009
  • Posts: 6509
  • Location: Lynden, WA.
  • Μολὼν λαβέ
Re: bullet seating depth?
« Reply #6 on: June 07, 2012, 07:39:53 PM »
No secret that you're not a beginner... ;)

-Steve
The NRA says I'm a Master!
Colt's, Ruger's, Dan Wesson, & Kimber are my friends!
Proud to be a U.S. Navy Veteran.

If you never follow your dreams, you'll never go anywhere.

Critical thinking keeps people from freaking the hell out every time some half baked blogger forgets his meds. Unlike some of you, I do not have TawkethOutOfAnus© syndrome.

Offline logan

  • Trade Count: (0)
  • Tracker
  • **
  • Join Date: Mar 2009
  • Posts: 45
  • Location: buckley,wa
Re: bullet seating depth?
« Reply #7 on: June 07, 2012, 08:55:26 PM »
i did not think to measure the actual bullet. thanks for the info.

 


* Advertisement

* Recent Topics

DR Brush Mower won't crank by jackelope
[Today at 11:12:40 AM]


2025-2026 Regs by hookr88
[Today at 10:30:18 AM]


Tooth age on Quinault bull by jeffitz
[Today at 10:16:48 AM]


HUNTNNW 2025 trail cam thread and photos by Feathernfurr
[Today at 09:50:13 AM]


KODIAK06 2025 trail cam and personal pics thread by hunter399
[Today at 08:22:05 AM]


Wyoming Antelope Unit 80 by tntklundt
[Today at 07:51:23 AM]


Stillaguamish 448 QD rifle tag by Turner89
[Today at 07:32:13 AM]


My Brothers First Blacktail by TitusFord
[Yesterday at 09:08:28 PM]


Pack mules/llamas by Shooter4
[Yesterday at 07:59:16 PM]


Kinda fun LH rimfire rifle project by JDHasty
[Yesterday at 07:01:44 PM]


Non-Shoulder mount elk ideas by Pete112288
[Yesterday at 06:45:10 PM]


SE raffle tags holder by redi
[Yesterday at 06:09:09 PM]


Dang bears... by Lumpy Taters
[Yesterday at 05:16:31 PM]


May/June Trail Cam: Roosevelt Bull Elk & Blacktail Bucks with Promising Growth by Lumpy Taters
[Yesterday at 05:13:15 PM]


Little Natchez cow elk by royalbull
[Yesterday at 03:39:11 PM]


Early Huckleberry Bull Moose tag drawn! by HillHound
[Yesterday at 02:14:44 PM]


Mason County Youth Buck Nov 1-16 by ASHQUACK
[Yesterday at 12:02:20 PM]


Selkirk bull moose. by 92xj
[Yesterday at 10:55:13 AM]

SimplePortal 2.3.7 © 2008-2025, SimplePortal